CFD Thermal analysis

04 April 2017 1 3K Report

Hi everyone,

I want to model the heat transfer of a ceramic block placed inside an oven. I have tried with a transient thermal study in ANSYS. Will a CFD study considering thermal properties like convection yield better results? Like similar to an CFD aero study; is it possible to perform a thermal study by considering the oven as the computational domain?

Thanks

Bin Zhao

Dear Buddhi,

I think it possible to incorporate the oven into computational domain. However, maybe you need to perform solid-fluid combined modeling for such domain. There are detailed information for this issue in the help file.

Badges
Science topic

More Buddhi Arachchige's questions See All

ANSYS coupled modal and thermal analysis

Dear everyone, I am looking for a method to do a coupled thermal modal analysis to see how thermal loads affect modal frequencies. I have tried this in ANSYS workbench, however I am not able to...

07 August 2017 3,847 8 View

Laser drilling in COMSOL?

Hi everyone, Is there a method to model laser drilling in COMSOL. I would like to see the thermal distribution through the thickness of a material during the laser drilling process. I suppose this...

02 March 2017 4,904 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View