Does anyone know, can i do cryosectioning of whole aorta after oil red O staining and use the cryosection parts for further analysis?

I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...

16 February 2021 5,876 2 View

Can I use the result from a pilot study to decide the minimum sample size ?

Can I use the result from a pilot study to decide the minimum sample size required to compare the means using independent sample t-test ? Or any other way that can help me to determine the...

29 January 2021 7,677 6 View

What is the best solution for counter electrode for perovskite solar cells at room conditions?

I'm investigating transparent counter electrode for FTO/PEDOT:PSS/MAPI3/PCBM layered perovskite solar cell. In my research lab, currently i have a glove box with N2 gas as a carrier. I'm goning...

21 December 2020 6,504 3 View

Yield of Plasmid is low in Maxipreparation of plasmid for 200ml? What might be the reasons for it?

Hi, I am working with a plasmid which is known to have very low copy number and when I am isolating it by midiprep alkaline lysis method, I am getting good amount of plasmid i.e., 16.56ng/ul....

11 December 2020 1,369 3 View

How to fix the fungus for SEM imaging?

I want to perform the SEM of candida sp. and i want to know that the fixation for the bacteria and fungus are different or same?

10 December 2020 6,169 3 View

My status has changed from "Awaiting Reviewer Score" to Awaiting AE Decision". Could the Associate Editor reject the manuscript at this stage?

Otherwise what this status means. If the Editor has received the comments from reviewer then why he is not sending it to Authors. As 10 days already spent till the status changed.??

18 November 2020 6,252 4 View

How to adapt a mature Questionnaire?

I am looking forward to seek some help regarding adaptation of mature questionnaires. I am new to quantitative studies and wants to use some demographic in my questionnaire, is it necessary to add...

08 November 2020 7,146 5 View

Is there a way to isolate nuclei without purifying cytoplasmic protein aggregates?

Hello, I am trying to isolate nuclei from HEK293T cells expressing a protein that aggregates in the cytoplasm, however when I run my samples in western blot the cytoplasmic protein is strongly...

02 November 2020 9,541 3 View

How can i fill zinc oxide or titanium oxide into etched pattern on glass substrate?

Hi! I need zinc oxide or titanium oxide to be filled into etched area on glass sbstrate. Etched are is being photolithography processed and being dry etched. Material must not present around the...

25 October 2020 152 7 View

How to get the most out of your qPCR data?

23 October 2020 7,537 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View