Simple description
Source to get Impact factor of journals
01 March 2021 6,654 2 View
I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...
28 February 2021 2,004 3 View
I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...
26 February 2021 9,580 4 View
25 February 2021 6,760 1 View
Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...
22 February 2021 7,528 3 View
I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...
17 February 2021 7,402 4 View
Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...
09 February 2021 6,799 8 View
07 February 2021 3,635 3 View
Hi, We find a specific distribution of electric fields in structure for different frequencies which can be seen using em solvers and known as modes. I would like to know how we can choose the...
04 February 2021 10,043 3 View
If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers can i use the same word in the writing of these 2 papers or this would considered as...
04 February 2021 4,648 4 View
Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...
23 February 2021 9,159 3 View
I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...
22 February 2021 4,290 1 View
we plan to induce colon cancer by injection. Cell lines derive from BDIX rats, but our experimental setting would favour SD rats. any experience?
23 January 2021 1,437 2 View
In Most pen injectors while dialing the dose, the dose dialer comes our or extends outside the pen as dialing happens. How much maximum extension of dialer is acceptable for performing...
17 January 2021 9,770 1 View
Hello, I would like to use the software Moldex 3D for the design optimization of an injection mould. How can I couple Moldex 3D with a MATLAB code? Any help appreciated, I wish you all a happy...
09 January 2021 569 2 View
Hello, I am using ANSYS Fluent for simulating the filling stage of an injection mould. However, when comparing the results with those of specialized software, such as Moldex 3D, I found the...
07 January 2021 7,992 1 View
I am injecting intrathecally (between L5-L6) , in rats, cannabinoid analgesics and I was wondering if they can reach the brain and have effects there as well ? Also I need to pretreat with...
07 January 2021 5,397 4 View
I am working with Balb/c mice, and in my experiment, I have to inject mice with antigens, then get their spleen and collect the splenocytes for fusion. Recently, I get into trouble with the mouse...
04 January 2021 3,591 3 View
Dear all, I am using corn oil as vehicle for subcutaneous injection and I want to reduce the viscosity of the vehicle (corn oil) to enhance the delivery of the main compound of interest....
18 December 2020 1,773 6 View
I was able set UDF for my dynamic mesh using following UDF. It works in serial mode. Now problem is that I want to speed up my solution, so parallelization is needed. I have gone through the user...
17 December 2020 420 4 View
