Can we use endogenous switching regression model in analyzing impact of any intervention using R-software? if so, can any one tell me the syntax?

More Guta Bukero's questions See All

Anyone who have experience on Phosphorus adsorption experiment?

I did phosphorus adsorption with an initial concentration of 25 Pmg/L, by biochar dosage of 5 grams in 100 ml phosphate solution, finally, I get 8 Pmg/L, which is logically high but by the...

19 August 2021 2,565 5 View

Which research journal publisher is the best in the world?

many journal puplishers are their in the world. but, among those pulisher, which one is the one?

25 December 2018 5,480 3 View

Is there better software than Remote Sensing and GIS for ground water potential mapping?

many software's can be used or Ground water mapping. but, recentyly is there new method or softwares?

25 December 2018 745 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Is there an alternative to a multinomial regression which allows the DV to be non mutually exclusive?

I am trying to analyse data from a survey examining what variables affect teachers perceived barriers to incorporating technology into their classroom. I have 5 predictor variables however my DV...

06 August 2024 1,752 3 View

In order to run Multinomial Logistic Regression, is it required that the data be in the long format?

I am using unit level data (IHDS round 2) & Stata 17

06 August 2024 5,725 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View