Can we use data in excel format or .nox in Zview software?

More Femina K Saidu's questions See All

How we can determine LoD of a voltametric sensor?

many answers are available here, which says the standard deviation of the blank should be taken for the calculation. But my doubt is how we can find out the standard deviation of the blank if we...

09 October 2019 9,525 3 View

WHY a composite material with conductivity as high as 10-4 S/cm shows high dielectric constant ( real part of permittivity as high as 6K) ?

I have done the dielectric measurement of conducting polymer nanocomposites containing some metal sulphide as nanofiller. And its d.c conductivity was in the range of 5-100 S/cm. when I measured...

09 October 2019 2,862 3 View

How do I calculate cysttalite size of layered fillers (hexagonal ) by using scherrer equation? is there any relation between its layer thickness?

I have incorporated layered fillers ( hexagonal crystal structure) into the conjugated polymer matrix. I would like to calculate the crystallite size of these filler particles. How we can apply...

08 September 2019 3,929 1 View

What should be the value of shape factor (K) in Scherrer equation for particle size of triogonal prismatic crytallites (honey comb- 2H)?

The layered nanomaterial i used belongs to triogonal prismatic crystal structure (honeycomb- 2H)

08 September 2019 8,291 2 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

Mohamed Tezeghdenti

You can analyse your data with Zview program. But at first you must change your excel file to notpad. I do it for you and attach here.

Femina K Saidu

Thanks a lot Sir@MohamedTezeghdenti

Alireza Razazzadeh

Hi, you can copy the data from excel to note,then you should delete the first and last line and save it. Now click the rename of the file and change the .text to .z and open the z view and click open data files and choose the file then click auto scale