Can we get differential equation for a very complex RLC circuit from simulink environment. Can we formulate (making equation) a complex RLC Circuit? Is there any easy way/method to do it?
yes
you could connect the simu link block as per your equation and simulate
If you are using SimPowerSystems toolbox I would suggest the command power_analyze.
in Matlab prompt command write something like
a=power_analyse('your_mode','structure')
the structure "a" now contains all that is required to solve the system.
regards
In some of the conference paper is published in the journal. Please share your information if you know such a conference where conference paper is published in journal/ repudiated journal. Your...
01 February 2017 9,491 4 View
I am using Microsoft power point for drawing circuit diagram, but it takes much time to draw. Is there any other easy tool to draw circuit diagram easily taking less time. Please guide me on this...
01 February 2017 2,484 1 View
Respected Sir Is it possible to run a simulation circuit (in Matlab/PSPICE environment) continuously to get optimum output for changing the value of a particular component? Optimization in...
06 July 2015 2,058 6 View
State electricity Corporation run in profit if the corporation have good Manager (Senior Engineer) to manage. Many person are involved with this management like Director, CMD, Deputy General...
06 July 2014 5,205 1 View
In general electricity people (employees) goes for inspection in urban/ rural areas sometime as a regular inspection and sometime as per information. Many times it is not possible to inspect all...
05 June 2014 1,777 12 View
If the circuit simulation is simple then it is very easy to express the output waveform with mathematical equation. It becomes very difficult when circuit becomes complex. Is there any simulation...
02 March 2014 8,135 9 View
I am using Orcad PSPICE 9.2 (Student version) Capture CIS Simulation Environment for Circuit Simulation. It is very easy to save Simulation Output Waveform in word. Windows--Copy to...
02 March 2014 1,352 12 View
Is it possible to run an optimization program (in MATLAB) whose objective function is the output of circuit simulation (in PSPICE----Orcad Capture).
01 February 2014 1,279 1 View
There are many areas in electrical as well electronics engineering where we can apply optimization to minimize objective function. For example to minimize Total Harmonic Distortion (THD) in...
31 December 2013 4,245 9 View
Please see attachment in the link below. In the attachment, I am trying to classify rectifier elaborately (uncontrolled and uncontrolled). Rectifier can be classified in many types, sub types. Is...
31 December 2013 6,572 12 View
I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...
25 February 2021 5,435 2 View
How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?
22 February 2021 3,697 1 View
Dear Professors, Colleagues and Friends I need to develop a simple Matlab/Simulink model of reverse droop controller for a simple LV MG. How can I get a simple one to use it as a sample? A basic...
22 February 2021 8,647 2 View
[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...
16 February 2021 5,060 10 View
I have a thesis on Utilize the electrical power from Regenerative Braking in 750 Vdc Traction by simulation in the Program MATLAB Simulink. I made the Power Load flow from 24kV to Traction...
08 February 2021 2,532 1 View
Hi, I have to design a digital model of different types of lighting. Is it possible to simulate the lighting level from different sources (LED, incandescent, mainly fluorescence) with matlab...
28 January 2021 3,818 10 View
I am doing a project with PV array in Simulink. When I run small section of the total system i do not get an error. But when i integrate full system(my system model`s are completely okay) I get an...
18 January 2021 685 10 View
How to build aero engine fuel system online prognostics simulation model using Matlab, Simulink and Simscape?
17 January 2021 5,181 1 View
I am designing a control system for Hybrid renewable energy systems using Matlab/simulink/simscape, but currently having a problem. Whenever I run the simulation, I get the error shown below. "The...
12 January 2021 2,142 5 View
How to implement max Log MAP algorithm turbo decoder on FPGA? Simulation is done on MATLAB. What are the next steps to be followed? Do I need to use HDL Coder feature in MATLAB? Is it needed to...
07 January 2021 4,405 4 View