What is the effect on the conductivity of the thin film during the process of thermal evaporation ?

Why thermally evaporated (VCM 600 V1 configuration of the thermal evaporator) CdTe film found n-type not p-type conductivity whereas all CdTe films deposited by varying the source to substrate...

23 November 2020 7,427 3 View

Can I analyse NGS DATA from an EXCEL spreadsheet?

Hi, I have Fold expression of RNAseq data obtained from Ion Proton sequencer and got the fold change data with mean in an excel sheet. now can I analyse this fold change data using any...

20 October 2020 2,240 3 View

Monolitic construction of brick masonary and concrete simultaniously have any effect ?

Concrete column casting after masonary completed monolithic.

17 August 2020 7,172 3 View

Rentraint Corner of building if need extra stitching diagonal reinforcement ?

If temperature reinforcement already provided ,at reentraint corner need extra diagonal reinforcement ,if needed then what amount of steel.

12 August 2020 1,707 2 View

No title

26 July 2020 1,511 0 View

How to calculate Time Average data (WSS, Velocity, Pressure) in ANSYS Fluent ?

I am doing a blood flow research for which Time average data of Velocity and Wall shear stress is important. The study is transient and my flow time is 0.5 sec. I save data with time step size of...

07 July 2020 4,323 2 View

What is the best management strategy for Diamond Back Moth (DBM) in cole crops?

What should be the best managemnt option for suppressing the DBM problem that farmer can take into consideration?

11 May 2020 4,280 1 View

Is it a good idea to retract a submitted article as the journal is taking too much time to make a decision?

I had submitted a research article related to the field of mechanical engineering (CFD) on the last December, 2019 in a Scopus Indexed journal. It has been around 6 months but the journal...

11 May 2020 9,286 8 View

Where can I get details of SARS-CoV-2 infected patients?

I have been working on peptide vaccine for SARS-CoV-2 or COVID-19 and also recently published some analysis on mutational changes in this virus. It would have been really helpful if I could get...

05 May 2020 2,749 9 View

How does the chemical etching (using HF) affect the temperature sensitivity of a fiber Bragg grating (FBG) inscribed in silica fiber?

Due to chemical etching, the cladding diameter of the silica fibre decreases with time. How does this reduced cladding diameter affect the temperature sensitivity of an FBG, which is inscribed on...

17 April 2020 4,771 2 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

Which fluorescent dye to use for measuring total ROS production?

Is DCFDA appropriate for measuring total ROS production, or can it only detect certain types of ROS? If I want to measure total ROS production, which dye should I use?

01 March 2021 9,447 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View