the link to journal website is
http://www.techscience.com/cmes/
Is this journal still in working mode as there is no way to track or contact them.
They dont reply to emails not ever telephone calls
so if anyone can help plz share
You have to submit your paper through their paper management site.
http://www.techscience.com/cmes/manu_script.html
The latest issues of this journal have been published in 2015 for now. If you have to submit your paper for publication, you can submit through the link provided by Mr. Ian Kennedy.
1. what is the meaning of negative value of of mode-1 stress intensity factor?? 2. What is the meaning if mode-1 Stress intensity factor is less then mode-2 stress intensity factor
05 June 2016 5,817 0 View
Respected fellow researchers Plz help me understand the basic methodology and code of XFEM for analysis of fracture and suggest some papers for the same
04 May 2016 7,543 1 View
i want to create a plate model with FGM properties the specifications are as follows length of plate = 2 height of plate= 3 young's modulus variation E(X) = E1*exp((log(E2/E1))*x) where E2 =...
07 August 2015 4,690 8 View
HOW CAN I EXTRACT NODAL AND ELEMENTAL DATA FROM ANSYS TO BE USED IN MATLAB. FOR EXAMPLE I MAKE A 2-D PLATE AND MESH IT I WILL GET NODAL CO-ORDINATES AND ELEMENT NUMBERS e.g. N , , 6 , 6N , ,...
06 July 2015 6,399 18 View
i have a function G = x1*exp(eta*pt(1)) where pt(!) are the x co-ordinates of points on a line. how can i plot it in MATLAB
05 June 2015 4,263 0 View
thanks
04 May 2015 9,867 0 View
here is the example of index used in an EFGM code [index] = define_support(node,pt1,di); function [index] = define_support(node,x,di)% find nodes in neighbouring of point x% Inputs:% node :...
02 March 2015 6,489 6 View
as there is material property variation along orthotropic directions so how to define these in MATLAB?
02 March 2015 3,381 0 View
I have to define a point in three different regions like if point 1 is < L/4 then out put is 0 then if point lies between L/4 and 3L/4 output is 2 and if point is >3 L/4 output is 6. I am...
02 March 2015 6,519 5 View
i want to rotate the square hole shown in the figure to 45 degrees to get the figure shown in attached file
02 March 2015 5,618 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Is this website real? https://isar.org.in/event/registration.php?id=2434532
08 August 2024 484 1 View
A website software of Blackbody radiation law expert software can used through the following web site. http://39.105.188.151:3000/index
07 August 2024 1,706 0 View
I have face this problem anyone help me how to solve this issue ?which is below Fatal error: There are inconsistent shifts over periodic boundaries in a molecule type consisting of 78 atoms. The...
07 August 2024 2,598 1 View
I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.
06 August 2024 6,796 3 View