How can I find about new sensors used in cars?

i am searching for new sensors that is used in cars for effective performance of motor. can you give me a book or paper or introduce me a site?

31 December 2014 4,104 4 View

Which element is usable for simulating a pre-twisted blade in ansys?

I want to model a twisted blade in ansys and nonlinear dynamic analyses, but solid element is not match with beam element and they are very different result. Now I don't know I select which...

08 September 2014 8,940 4 View

How can i writing a paper for ISI journals?

As you can see, my English language is poor specially in writing. i want writing a paper. i writed that fully but i have so wrongs in writing. are there any software that help me? what can i do...

07 August 2014 6,531 3 View

why plastic zone in Abaqus is low?

whenisimulate my CT specimen in Abaquse with Elastic-Plastic propertic my plastic zone in crack tip is lower than experimentall. i obtaine true stress and true strain from tensile test with this...

06 July 2014 6,019 6 View

What are the parameters max principal stress and fracture energy in analysis XFEM with Abaqus?

06 July 2014 1,891 3 View

Why can my XFEM method in Abaqus not predict crack grows?

When I use the XFEM method in Abaqus to predict fracture of my materials, Abaqus gives good results about crack initiate and maximum load, but it can't predict crack grows. In Abaqus, after...

06 July 2014 4,076 19 View

How can I find the coefficient for fitting a curve in MATLAB?

I fit my data in MATLAB with a function and I can see the results and coefficients in the command window. I need this coefficient in order to continue with my codes, but I can't input this...

05 June 2014 827 10 View

Why is this error in abaqus XFEM method: too many attempts for this increment?

I simulate crack grows for a specimen in abaqus and use XFEM method. When my crack initiates and grows a bit and before full break the specimen I faced this error: too many attempt for this increment.

02 March 2014 4,078 31 View

Does anyone have experience with damage when using XEFM methods?

When I simulate my specimen with XFEM method I have faced an increment error. But when I decrease displacement or decrease the element of mesh the error disappears. I don't want to decrease the...

01 February 2014 2,312 1 View

Can I determine fracture toughness of a material with Abaqus?

I want use the data of tensile test of a material to determine fracture toughness of a material. What information do I need? Is it possible?

01 February 2014 7,474 12 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View