Can Materials studio apply an ultrasound field?

16 November 2022 0 626 Report

I want to use Materials studio to study the effect of ultrasonic cavitation on high temperature non-metallic oxides. Is it possible to set up ultrasonic cavitation in this software? Thank you for your answers.

Badges
Science topic

More Shiyan Jiao's questions See All

How can i get the meaning of variable "oin" in WRF-CHEM?

Hello, I am learning WRF-Chem, and there are some doubt I have not get the real answer. I used the chemical mechanism of MOSAIC for aerosol in WRF-Chem, where there is a variable called “oin” that...

17 May 2024 4,530 0 View

How to evaluate airport runway wet pollution effectively?

Wet runway refers to an airport runway whose surface area is covered with moisture or deep water of no more than 3 mm within the length and width of the runway being used or planned to be used....

22 May 2023 6,754 2 View

How long can bioethanol be stored at 25 ℃?

Under sealed conditions, the storage time may be long, but how many years is it?

02 May 2023 5,029 0 View

How does Ph affect azo casein ?

Azocasein was used as substrate and hydrolyzed under protease. The location of characteristic peaks was different under acidic and alkaline conditions. It was wondered under which conditions...

19 April 2023 6,435 2 View

Could anyone tell me what's wrong with my electroporesis band?

i used the denatured collagen sample which was treated by 100 temperature, collagenase with 50U and trypsin with 0.1% for 10 mins, and put 7ul denatured collagen into each well. SDS-PAGE was...

18 November 2021 181 5 View

Any recommendation on SaCas9 antibody?

Hi, does anyone know a good SaCas9 antibody for IHC or immunofluorescence on mouse brain slides? We gave a try with the Epigenetek monoclonal antibody (A-9001) without antigen retrieval (1:500)...

29 December 2020 4,702 5 View

Why GFP fluorescence disappear in nude mice?

ESCC cell line KYSE180-GFP (GFP lentivirus transfected into KYSE180) were subcutaneously injected to nude mice. GFP fluorescence is properly detected under in vivo imaging system 7 days after the...

04 May 2020 8,250 4 View

How to use LS-DYNA for numerical simulation of millisecond blasting?

Hi, guys: When I use ls-dyna for the numerical simulation of millisecond blasting, I find that my explosives (after initiation) are always affected by the explosives with the first initiation...

06 April 2020 5,314 0 View

Can someone help me with the over-large H2 Faradaic efficiency in a measurement of CO2 electroreduction?

Hi, I have recently learnt to measure the gaseous products of CO2 reduction on a copper foil electrode. The method I use is an in situ gas chromatography, which has been widely reported in the...

20 December 2018 5,787 2 View

Why pretreatment of drugs before induction of disease in cell culture work?

Among all the literature and protocols I came across, the drug testing will always be carried out in a pre-treatment of cell with drugs then followed by disease/injury induction manners. For...

01 November 2018 3,203 3 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

How can you draw a coordinate bond between a metal and donor atom in metal complexes, using discovery studio visulizer software?

Hello,, The metal complex ligand appears incomplete in the screen of the discovery studio visualizer

30 July 2024 3,354 1 View

How to prediction 2D to 3D aptamer?

Hello, I have a little problem. Well, right now I only have the DNA aptamer sequence. I went to see the 2D model form with DNA folding. After that, I used RNA Composer to simulate in 3D and used...

30 July 2024 6,794 0 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Why in 2D image created by discovery studio 2021, the halogens appear as alkyl group?

In my molecule there is Chloro group at 2-position of phenyl ring, but in 2D image it appears as methyl showing no interaction.

28 July 2024 734 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

Wrong out put for gmx x2top?

Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...

24 July 2024 367 4 View

What binder would be the best choice to modify glassy carbon electrode with a 2D Material like Graphene or MXene?

I am trying to drop cast 2D Materials on Glassy Carbon Electrode for Cyclic voltametry and EIS purpose. What would be best binders to use?

23 July 2024 5,776 2 View