Can i uncoat my gelatin from cell culture flask?

04 April 2019 1 2K Report

I have coated my culture flask with more concentrated gelatin than required accidentally. I haven't seeded my cells yet. Can i uncoat them and again coat them with desired concentration?

Anupam Ruturaj Tripathy

Generally, i use PBST to remove gelatin from my coated surface & sake it for 2 to 3 hour. After that i clean it using DIO.

Badges
Science topic

More Paroma Deb's questions See All

How to preserve and process endocervical swab for cytokin analysis by flow cytometry?

I wanna analysis cytokines level in different stages of CIN and ca cervix both in HPV DNA positive and negative cases. We collected 1000microliter cervical swab by cyto brush for detection of HPV...

02 March 2019 426 2 View

Can i use miRNeasy serum/plasma spike in control qPCR normalization kit (QIAGEN) for my EC sample obtained from HUVEC ?

I intend to see miR expression in Endothelial cells from HUVEC. I have some remaining miRNeasy serum/plasma spike in control cel-39-3p from another experiment. I am thinking to use it as qPCR...

10 November 2018 1,189 0 View

Can i use miRNeasy serum/plasma cel-39-3p spike in instead of U6 snRNA as control in qRT-PCR for miRNA of endothelial cell origin?

I dont have enough time to order for U6 snRNA,so what can i do instead? Please help me out!

10 November 2018 4,610 4 View

For assessing endothelial permeability change if i go for only VE-cadherin expression study in cell culture will it be appropriate?

For my MD thesis purpose I am going to see endothelial permeability change after treating them with Dengue infected patients sera. I will establish endothelial cell line from HUVEC. In most of...

07 August 2018 1,347 5 View

What are the methods for confirming cultured cells from HUVEC as endothelial cell & which one is most appropriate?

I am planning to establish primary endothelial cell culture from HUVEC and then to treat them with Dengue virus infected serum for further experiment. I need to confirm my cultured cell as...

05 June 2018 9,283 6 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the most effective way to sterilize camelina seeds?

I'm working on camelina seed sterilization and have some doubts about the process. I followed a protocol used by my lab mate, but I'm unsure about a couple of things: Is it safe to use 10% bleach...

02 August 2024 1,178 3 View

When should I stop watering A.thaliana for collect their seeds?

I have been following Rivero et al 2014 protocols, but I am not sure when I should stop watering because my plants are completely yellow but the siliques are not 80% brown. Any recommendations?...

30 July 2024 2,301 7 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How should I prevent mould contamination on small seeds in a petri dish exposed to warm temperatures?

Hello all, Recently as part of a research project at university, we have been studying the effects of light and temperature on eucalyptus seed germination. In our initial run of trials we...

24 July 2024 8,850 4 View

I accidentally removed 5 publications a few minutes ago. How can I add them again to my profile?

23 July 2024 9,145 2 View