Can i publish using simulation results ?

More Johneph Sukham's questions See All

SiO2 reactive sputtering Roughness ?

How can I reduce the roughness of Sio2 deposited using Si Target ? Lowering the O2 percentage might help or increasing the power .I am running the process at 3mtorr deposition pressure.

01 February 2017 3,420 6 View

Smooth thin film with pin holes probable reason ?

What could be the reason for the pin holes on thin film ? The roughness of the film is around 0.40 nm

08 September 2016 3,906 13 View

Minimum sputtering gas pressure for gold ?

What can be the minimum sputtering gas pressure for gold on LESKER so that a film is deposited?

06 July 2016 4,719 2 View

Is it required to adjust Aperture for each magnification in Scanning electron microscope?

04 May 2016 3,683 4 View

Gold thin film thickness measurement?

What can be the best thickness measurement of a gold thin film, thickness in the range of within 10 nms ?

04 May 2016 4,889 3 View

What are the some ways of smoothening a gold film deposited using Sputtering?

03 April 2016 9,105 7 View

Can anyone explain hybridized surface plasmon polaritons?

11 December 2015 2,666 5 View

Can anyone suggest a good material for sub-cycle imaging in real space?

Please can some one suggest a good material for SUB-CYCLE IMAGING IN REAL SPACE?

09 October 2015 683 1 View

Can anyone please tell how to add Graphene as a material in cst studio suite ?

In cst studio suite graphene is not listed as a material . I have read some papers that it can be added as a material too. Please tell me how to add as a material ?

09 October 2014 2,850 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Is an invitation to join the editorial board of Clinical Cardiology Updates a scam?

I received an e-mail invitation to join the editorial board of Clinical Cardiology Updates. While I have published a few articles related to cardiovascular disease, there are lots of colleagues...

06 August 2024 8,981 8 View

Why is the Protocol for Preventing Postpartum Hemorrhage (https://pubmed.ncbi.nlm.nih.gov/36113283/ ) not being widely adopted?

If the placenta is delivered in squatting position within 3 minutes of the birth of the baby, postpartum hemorrhage is completely eliminated. It works every time. It is quite likely that if a...

05 August 2024 8,895 0 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

How to restart MD without using checkpint file in GROMACS?

Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar

29 July 2024 3,084 8 View

How to prepare a molecule for molecular dynamics calculations?

If I want to calculate molecular dynamics (Gromacs), do I first need to optimize the geometry of the molecule? For example, I first draw the molecule in Avogadro, and then what? I guess I can't...

28 July 2024 673 3 View