Can I make Nanoparticle pellets for dielectric characterization without using any binder?

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Can chitosan alone can act as a reducing agent for Cu(0) nanoparticle sythesis?

[Synthesizing Cu nanoparticles without using chemical reductants]

01 March 2021 8,359 1 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

How can I calculate the rdf of water molecules around 'Na' ions that are closest(adsorbed) to the nanoparticle(solute)?

Hi, I want to calculate the radial distribution function for water molecules around the Na+ ions adsorbed on the surface of a spherical nanoparticle using the gromacs trajectory dynamically? For...

28 February 2021 5,650 1 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Omid Amiri

You can apply pressure like prepare pellets for FT-IR measurement.

Mohd Asif

Dear Omid Amiri,

For FT-IR measurements, we use KBr as binding agent. I tried making pellets without any binder but pellets broke as soon as I removed them from die.

Thanks for the answer.

Lina L. Sartinska

You will get oxides on the surface of nanopowders and change composition In the case of water. It is difficult to make pellets without binder. So, you should create bypass. You should produce 10 pellets with different binders: With oxygen, without oxygen, protonic and aprotonic heptane gecsan and so on. Measurements will show effect of binders on your properties more or less