I plotted of graph of volume concentration versus viscosity for a particular nanofluid. i got a straight line graph. i would like to know if this graph can tell me if the fluid is Newtonian or Non-newtonian?
No, because I didn't run experiment for that
Dear Chidozie,
can you provide some more information? Do you have some other date, which could be used, or it is only volume concentration and the viscosity?
Best regards,
Antoni Artinov
It's only volume concentration and the viscosity relationship that i have
Why does Ethylene glycol produce greater enhancement on heat transfer rate than water as its flow through a tube, considering that water has a higher thermal conductivity. What could be the...
01 February 2017 8,592 2 View
Why Ethylene glycol does has produce greater enhancement on heat transfer rate than water its flow in a tube, considering that water has a higher thermal conductivity. What could be the possible...
01 February 2017 7,091 5 View
I am measuring the thermal conductivity of CuO/EG nanofluids experimentally. At low volume concentration of 1 and 2%, thermal enhancements are very high. At 3 and 4% vol. conc., thermal...
06 July 2016 2,793 6 View
Can these two correlations be used in computing the average Nusselt number for cone shaped helical coils? The correlations are written in the attached file.
05 June 2016 2,451 0 View
I am carrying out mesh independent study on fluid flow in curved tubes. I am trying to vary the pitch of the curved tube. So, I have various coiled tubes with the same dimensions but with varying...
04 May 2016 910 1 View
I need help in analysing some TEM micrographs of imaging of nanoparticles. I have interpreted them but need to see interpretation of some other professional. I would love to have your email to...
04 May 2016 1,586 4 View
I want to measure the stability of alumina nanofluids at volume concentrations of 1-5vol. % concentration. The UV-Vis spectrometer needs me to dilute my samples before light can pass through. If...
01 February 2016 6,074 5 View
Also, in order to ensure stability of the dispersion, to what pH value do I adjust the sample to? Lastly, do I mix the AlN powder with the base liquid before adjusting the pH? or do I mix the acid...
01 February 2016 3,720 1 View
I am drawing my model in Autocad 2010 and importing into Ansys. After my simulations, the results I got where incorrect. Does drawing my geometry have something to do with this incorrect result?
11 December 2014 8,918 5 View
Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.
09 August 2024 2,111 2 View
I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...
03 August 2024 6,070 3 View
I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...
31 July 2024 9,697 0 View
The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...
30 July 2024 3,126 0 View
Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.
29 July 2024 4,971 1 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...
25 July 2024 9,058 4 View
I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....
24 July 2024 4,058 5 View
The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...
24 July 2024 9,644 1 View