Can salting out effect in block copoymer templated mesoporous material increase its surface area?

Increase in salt concentration (NaCl) in presence of block copolymer can generally increase the mesopore diameter and decrease the no of micropore. Is there any way that it can increase the...

06 July 2017 1,295 6 View

During water oxidation in presence of organics why there is shift towards negative potential in the current potential curve of oxygen evolution?

02 March 2017 8,648 3 View

How to make solid state charge transfer complex between Tetracyanoquinodimethane (tcnq) and graphene?

02 March 2017 2,535 2 View

For symmetric supercapacitor can i go to negative potential window?

I am making a symmetric supercapacitor. can i go to negative potential window.As its a redox active material shows pseudo peak in a potential window of -0.3 to 0.4.I am attaching the papers who...

11 December 2016 2,257 10 View

Can the optimisation of mass in two electrode for assymetric supercapacitor be done from two electrode experiment?

If anyone is having the reference please provide it.

11 December 2016 1,818 1 View

Increasing ratio of inorganic precursour to triblock copolymer concentration can increase the interparticle void space,pore volume and surface area?

What could be the reason for increase in surface area with increasing inorganic precursour concentration.The ratio of surfactant to water is constant.please reply.

10 November 2016 5,953 0 View

Increasing ratio of inorganic precursour to triblock copolymer concentration can increase the interparticle void space,pore volume and surface area?

Please reply.

10 November 2016 444 0 View

Is it essential to put the EIS fitting plot in the manuscript? or we can go with the raw data plot and the value obtained from the fitting?

give reference if you have any where ac impedance raw data has been plotted and circuit values are given in the table. but EIS fitting data has not been plotted.

31 December 2015 7,844 7 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

Where can I find atmospheric measurement profiles (temperature, density, etc.) between 300-800 km altitude?

I am investigating thermospheric mass density profiles between 300-800 km altitude. I would like to compare the variability with other parameters, including temperature, electron content,...

01 March 2021 5,902 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View