How to improve the MAPE and reduce the residual mean value in Time Series?

I have created a time series model and the mean of residual is -21.34 and the MAPE value is 10.64616. So with what value i shall go with and is there any option to fine tune the time series model?

24 December 2019 7,461 3 View

Kindly suggest few anti-inflammatory non steroidal anti inflammatory drugs that can suppress major inflammation par with steroid ?

Non steroidal Drugs that can be comparable for anti inflammatory property like steroid... kindly suggest

17 January 2018 9,872 2 View

Does anyone have the full text of the publication - Star-Branched Block Copolymer Ionomers: Synthesis, Characterization, and Properties?

I am looking for the full text of the article Published by Dr. Scott E. George 05-13-1991 along with Dr. Robson Storey and Dr. Mark Nelson. Abstract A new kind of telechelic ionomer has been...

25 December 2017 7,760 1 View

Taking Goodman, S. A., & Svyantek, D. J. (1999). questionnaire for job performance ?

For my Ph.D. study " Impact of Emotional Intelligence on Performance of Employees and Organizational commitment in Software Industry" for this I have taken Goodman scale of 18 items of Contextual...

23 September 2017 621 6 View

How different is western blot protocol for phosphorylated protein from regular western blot?

30 August 2017 2,594 9 View

Can anyone give me a protocol for stable luciferase transfection of murine cell lines?

I want to do a stable luciferase transfection of murine PDAC (PANC02) and colorectal (CT26) cell lines. Please help me find where to obtain the protocol and reagents. Thank you. Sincerely, Lakshmi.

05 April 2017 2,462 4 View

After Extraction of pore solution from cement concrete, how can we findout the concentration of each content?

14 November 2016 2,958 3 View

Whats is the maximum concentration of NaOH that is not toxic to cell cultures?

18 September 2016 998 6 View

How to analysis the lotgering factor for Textured BaTiO3?

I know the formula for lotgering factor but i am unable to get the correct values as published in journal

01 July 2016 5,368 1 View

Can anyone suggest why I do not see amplification in Real Time PCR?

14 January 2015 5,497 8 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View