Can grain structure be revealed using SEM?

27 December 2017 1 4K Report

can we see the grains and grain boundaries without using any etching procedure by SEM?

yes!and it is completely useful for many researches. for example that is a SEM image of a grain boundary in a galvanized steel surface which was used in a corrosion characterization.

Badges
Science method

More Hossein Ahmadi's questions See All

Is there an English Translation of the Carl Moller text: ZUR VERGLEICHENDEN ANATOMIE DER SILURIDEN?

I recently came across an anatomy text by Carl Moller that was published in 1915 but it is in German or Dutch neither of which I can understand. I would like to know if there is an English...

10 August 2024 4,347 1 View

How can I find access to heavy metal reference doses from the EPA and WHO websites?

Reference dose and Maximum acceptable concentrations HMs

03 August 2024 8,230 4 View

What publications should I target as a psychology masters student in the UK?

I am writing a paper as a part of my course. I am new in London and was wondering that what publications should look upto?

21 July 2024 3,538 1 View

I have two problems: 1) the enzyme is not immobilizing efficiently into the MOF material.. 2) the MOF itself has peak on 400nm by using p-NPA test.?

I am working on carbonic anhydrase immobilization into MOFs. I am facing problems with low enzyme loading.. The other issue is that when using p-NPA activity test to detect the activity of the...

20 July 2024 1,440 3 View

What analysis to use for an dependent variable with repeated measures and a independent variable only measured once?

Hi all, I am trying to use mixed effect model to analyze my data, which including a baseline measurement for my exposure (A), and repeated measurements for the outcome (B). I do have some...

17 July 2024 8,682 3 View

I need to know the required time for VDF heating with water for 50-80°C for PVDF Polymerization in ?

i need to know the required time

15 July 2024 4,796 2 View

How can I quantify MDEA (N-Methyldiethanolamine) with a GC-FID?

I have a mixture of glycol, water, MDEA, and piperazine. I want to analyze it with GC-FID.

15 July 2024 9,652 3 View

How can I quantify MDEA (N-Methyldiethanolamine) with a GC-FID?

I have a mixture of glycol, water, MDEA, and piperazine which I want to analyze with GC.

15 July 2024 2,181 10 View

How to classify 3D Bioprinting as a part of Additive Manufacturing?

Hello, I have a problem in classification of "Additive Manufacturing" techniques. There are several classification for Additive Manufacturing e.g. Powder, Extrusion, Resin etc. Actually, I am OK...

15 July 2024 139 3 View

What analyzes do you use to compare biodiversity in a square, at two different times?

e.g. moment one: square in its normal state moment two: square after cutting large trees and replacing them with dwarf trees.

12 July 2024 8,258 5 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View