Can anyone tell me that which are the advantages and disadvantages of SWAT & RUSEL Model ?

More Amol Pandurang Jarag's questions See All

Can anyone tell me that which are the advantages and disadvantages of SWAT & RUSEL Model ?

I need it to my research in Hydrological modeling.

09 October 2015 9,937 1 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Liem Nguyen Duy

In SWAT model, MUSLE is used for calculating sediment loads.

I am not sure which problem do you care about SWAT model?

Vikramsinh Pawar-Patil

Dear,

Basically SWAT is very Data Hungry Model but quite useful in order to get runoff and sediment yield. RUSLE is also useful to get potential soil erosion. Both models are good but some of the values which are required in the formulea for our region is difficult to get and as far as assessment is concerned it is very difficult to get real time result.

Go ahead. Best luck.

Amol Pandurang Jarag

Thanks Sir