I have deposited cds on ITO by electrodeposition. Now I want to create sharp step in film for profilometry measurement (thickness). So I want to know how to create sharp step in film either during deposition or by using suitable etchant.
what's cds? Is it CdS cadmium sulfide, or is it something else?
Yes,it is cadmium sulfide...
As-deposited CdSe films have very high resistance.What materials doping can be used to increase the conductivity?
01 February 2015 9,954 7 View
Can anyone explain in brief how to prepare the solution for ternary CdSexTe(1-x) thin films e.g. CdSe(0.6)Te(0.4) thin film?
09 October 2014 9,993 2 View
How solid solution of CdSe/PbS leads to optimum band gap?
08 September 2014 7,385 2 View
Can anyone suggest a reference electrode for electrodeposition in aqueous solution? Which one is better between a Saturated Calomel Electrode (SCE) and an Ag/AgCl reference electrode?What is the...
03 April 2014 9,953 22 View
How much feasibility of electrodeposition of SnS layer on electrodeposited ZnO nanostructures to form the ZnO/SnS heterostructure? What is the future scope of this type of heterostructures for...
03 April 2014 4,110 5 View
Ca anyone suggest some Indian manufacturers of reference electrodes e.g. SCE or Ag/Agcl for electrodeposition purpose in aqueous electrolyte. I have references of some companies outside from India...
03 April 2014 4,342 1 View
I want some information regarding reference electrodes e.g. SCE or Ag/AgCl of various companies and of which supplier should be in India and cost should be less than Rs.15000.
03 April 2014 4,641 3 View
On which parameters does the thickness of absorbing layer depend?
31 December 2013 1,433 3 View
Light trapping.
31 December 2013 4,548 1 View
.
31 December 2013 7,347 5 View
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,801 2 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...
06 August 2024 3,176 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
How can I measure the thickness of thin film by Uv-Vis?
06 August 2024 7,810 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...
04 August 2024 5,974 3 View
Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?
03 August 2024 7,035 3 View
I need something like Camag's VisionCat software for photodocumentation of TLCs. Could you recommend something?
31 July 2024 8,415 1 View
Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...
30 July 2024 8,339 2 View