Can anyone suggest a program for protein modeling to visualize the effects of mutations on protein structure?

Esmat Fazel-Najafabadi @Esmat-Fazel-Najafabadi

11 August 2013 1 10K Report

I have already used SIFT, polyphen, Mutationtaster and a couple of other softwares. I am now willing to work on protein modeling and see how a specific mutation can change protein structure.

Naresh K. N.

You can try using TRITON software. Link: http://www.ncbr.muni.cz/triton/

This is a software for in-silico protein engineering.

Badges
Science topic

More Esmat Fazel-Najafabadi's questions See All

How can I create a knee reinforcement motor in OpenSim software? Is there a ready model that I can use?

I need to put an extra motor on the knee to do part of my project. The process of doing it is needed in the use of other software and sub-programs.

03 July 2024 6,038 0 View

Is it possible to get reaction times in ERPLAB BLINLISTER?

Dear Researcher, I was wondering whether it is possible to acquire reaction times using EEGLAB/ ERPLAB. Are there any suggestions on getting reaction time for a large number of conditions and...

28 April 2024 1,503 0 View

Can thigh muscles withstand pressure in load-bearing system?

I have designed a system for load-bearing from a damaged leg, as shown in the figure. Upon descent, it activated an active mechanism to prevent direct contact between the leg and the ground. I...

05 January 2024 9,431 0 View

Can Leveraging Healthy Walking Patterns Improve Knee Function for Individuals with Weakened Knee Muscles?

The knee assistive system has been developed based on the pattern of walking in a healthy individual using fluidic muscles. We have aimed to utilize this pattern to enhance the functionality for...

05 January 2024 1,668 0 View

Does connecting the upper part of the exoskeleton to the middle part of the thigh pose any risks or potential muscle impairment?

I have designed a lower limb exoskeleton that is supposed to take the extra load off the injured knee while walking. Is it correct to connect the upper part of the exhaust to the middle part of...

23 December 2023 8,148 0 View

Can Torque Motors Replace the Torque Power of Healthy Individuals for Elderly Individuals with Weakened Knees? Are There Better Suggestions?

I plan to replace the torque power of a healthy person in the form of a torque motor for an elderly person with a weakened but healthy knee. To what extent is this hypothesis true? Is there a...

22 December 2023 992 0 View

What is the amount of knee reaction force during the gait?

I am facing the following sentence. Is there any experience with this? about 1/3 of the knee reaction comes from the body weight – the rest is from the compression caused by the muscles spanning...

13 April 2023 3,424 2 View

Dimension limitation of the electromagnetic unit cell simulation?

Hi, Is it necessary to simulate the unit-cell using FEM (HFSS, CST), its dimensions should be less than a wavelength? In other words, there is no dimensional limitation of the structure in the...

21 November 2022 9,562 3 View

Comsol Multhiphysics pre or post processing. perform of logical operation on two distinguished local variable?

How can I add or subtract (logical operator) the values obtained from two points in Comsol software? the values are valid on specified location, so i cant add or subtract results automatically....

27 July 2022 192 0 View

Absorber layer to decrease side lobe level?

What absorber material is suitable for the reflector antenna to reduce back lobe level? I would appreciate any suggestion and comments.

25 December 2021 4,621 10 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

What precautions should be taken while handling S. aureus enterotoxin Type B in the lab?

I would like to understand potential safety concerns while handling SEB in the lab. Especially while working in animal house facility. Would like to know precautions for handling. Sigma MSDS...

07 August 2024 6,034 3 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View