Can anyone share a tutorial for bispectrum feature generation of thermoelectric alloys?

Ashwani Kushwaha @Ashwani-Kushwaha

16 February 2023 0 6K Report

Development of Machine Learning based SNAP potentials for thermoelectric alloys

Badges
Science topic

More Ashwani Kushwaha's questions See All

Can someone add Journal Impact Factor Document (JCR 2024)?

Clarivate Reveals World’s Leading and Trusted Journals with the 2024 Journal Citation Reports on 20 June 2024

19 June 2024 3,601 2 View

Minimum concentration of protein to be injected for detectable peaks of protein in 16/60 Sephacryl S-100 HR column for SEC-FPLC?

Hello Peers, Warm wishes to all. I am a new user of the Cytiva AKTA Start system for SEC with a column, HiPrep 16/60 Sephacryl S-100 HR (120 ml column volume). I am not sure about the minimum...

03 June 2024 7,713 2 View

How to split molecules into test and training set in 3D-QSAR?

Hi peers and experts! I am new to 3D-QSAR and tried to build a model based on 34 molecules, split into 10 test and 24 training sets. In the end, a poor model is evident from r2 and q2 values....

08 April 2024 2,785 6 View

During galvanostatic charge-discharge (GCD) measurements, why is the electrode not fully charged when lower currents are used ?

When applying currents ranging from 1 to 8 mA to charge my electrode, it fails to reach full charge, and instead, after some time during the charge cycle, it exhibits a straight line pattern on...

28 February 2024 1,535 3 View

What is Repeated Earthquakes?

What is the concept of repeated earthquakes? How does the dynamic analysis is performed under repeated earthquake? Is this done in a different way that IDA analysis? How the ground motion data...

02 November 2023 4,884 4 View

While doing simulation on SCAPS-1D for the CdTe/CdS solar cell, I am getting a negative QE for higher wavelength range?

I required some data for the study related to QE of solar cell, but the problem is that I am getting negative QE values at higher wavelength range or at photon energy less than the band gap of...

11 October 2023 5,729 0 View

Does the results obtained with the cracked version of SAP2000 match with licensed version of SAP2000?

I am trying to verify the results obtained by modal analysis and response analysis of a G+4 RC hill Building with the base paper results but unfortunately couldn`t. Although I have followed all...

09 October 2023 7,390 9 View

What are the technical aspects of microstrip patch antenna for space/defence applications?

Related to antennas arrays.

03 October 2023 568 2 View

Why my Ni structure is not converging after applying a strain in X-direction?

Please find the attached Ni Quantum Espresso Input file. &CONTROL calculation = 'scf' verbosity = 'high' restart_mode = 'from_scratch' tstress = .true....

11 September 2023 9,925 0 View

How is RINEX data converted to SP3 or SINEX?

Converting Rinex data to other geodetic file formats is essential for compatibility and interoperability between different software tools used in GNSS data processing and analysis. Two common...

05 August 2023 7,873 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

How the electron and hole pocket near the fermi level in the band structure affect thermoelectric properties of Topological half-Heusler compound?

How the electron and hole pockets near the fermi level in the band structure affect the thermoelectric properties of the topological half-Heusler compound?

26 June 2024 2,933 0 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View

Is there any suggestion on the explanation and reduction of stacking fault defects in high Al content InAlGaAs alloy lattice matched to InP?

24 June 2024 6,645 1 View