I need some good papers or reviews on the topic mentioned above.
The following highly cited articles will help you.
Thanks Omkar Singh
the following articles may be help you
These papers may also help you
Thanks Rana Afif and Mirta Stupak
Answered.
02 July 2024 2,942 5 View
As I understand if you use the mean and SD for describing your data, this means it is normally distributed and parametric. If so, the test for variance should be simple T test.
04 April 2024 2,331 3 View
I am extracting data from RCTs for conducting a meta-analysis, and confused with the data extraction step
29 January 2024 501 0 View
In fact, yes several researchers are thinking from the point of analysis only rather than trying to solve major research problems or questions. Therefore, the dilemma has also been shifted to...
05 August 2023 1,349 2 View
hello I have done a 50ns MD simulation production run on three different protein-peptide complexes. unfortunately, I am getting quite a high RMSD in all of them. I tried many things but couldn't...
24 July 2023 1,638 2 View
FinTech resistance is Dependent Variable Social Influenece is Independent Variable Technostress is Moderator
20 July 2023 4,653 1 View
I've done a 50 ns protein-ligand MD simulation. Getting stable RMSD for the first 20 ns, but it increases afterwards, and at some point frame, it's getting very high. My question is, is my md...
19 June 2023 1,163 3 View
Hi, I really need to replace the Qiashredder with a similar product. There is a number of companies that have competitive products. I would like to receive advice about them. Note: we work with...
10 June 2023 7,807 0 View
Hi, We will like to receive advice to improve RNA quality and quantity. After many trials and calibration, we get a protocol that gives better RNA quality and enough quantity for downstream...
10 June 2023 8,110 4 View
I've done 2ns protein-ligand MD simulation in two ways 1. first I used general MD simulation, generating every single file by commands as suggested in gromacs tutorial. As an output, I've got 200...
04 June 2023 9,418 4 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.
06 August 2024 6,796 3 View
Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice
04 August 2024 7,367 3 View
As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....
03 August 2024 7,304 2 View
Reference dose and Maximum acceptable concentrations HMs
03 August 2024 8,230 4 View
We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...
31 July 2024 3,900 2 View
Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...
31 July 2024 3,333 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
The Likert scale is a commonly used measurement tool in social science research to assess people's attitudes, opinions, or perceptions. The social science students still have difficulty selecting...
25 July 2024 7,535 1 View
In general, when performing a Tafel analysis for corrosion resistance measurements, a line voltage scan is performed from say -250 to +250 mV vs. OCV at low scan speed around 0.125 mV/s. However,...
25 July 2024 7,982 3 View
