How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

How to calculate time-averaged fields from Ansys CFX solver?

I would appreciate any comments on the following problem. I need to calculate mean fields (e.g. pressure, velocity and vorticity), for which I activate Trn Stats tab in CFX-Pre. However, what I...

21 February 2021 8,548 7 View

The most suitable turbulent models to predict flow past a floating body?

Hi all, I'm planning to simulate flow past a floating body using CFD method with the main purpose of investigating its stability against hydrodynamic forces. A sketch of the problem is presented...

28 January 2021 5,872 5 View

Stable region for VL model?

29 December 2020 4,125 3 View

How can I fix the capacity curve of two different structure?

I have two frames for nonlinear analysis, one of them is CBFs and one of them is BRBFs ( the generals are the same, only lateral elements are different). When I drew the capacity curve of my...

11 November 2020 10,034 3 View

How to measure the equivalent sand-grain roughness of a sandpaper?

I want to use standard sandpapers of different grit sizes to impart flow resistance to a surface. I am wondering how to convert the roughness of sandpaper to an equivalent sand-grain roughness. Is...

18 October 2020 9,384 3 View

How to calculate transvers current correlation function (MD)?

12 October 2020 4,424 1 View

How can I obtain thermal efficiency in thermal photovoltaic (PVT) systems by CFD (FLUENT) method ?

Hi everyone I have a question about the thermal efficiency of photovoltaic thermal (PVT) system by CFD (FLUENT) method. Why thermal efficiency in the morning with 400 W/m2 radiation is more than...

13 September 2020 2,543 4 View

How to deal with ANSYS Q3D surface mesh generation error?

I am trying to extract the stray inductance of a PCB bus bar using ANSYS Q3D. I tried different types of meshes but every time in the middle of the simulation, this error "Surface Mesh Generation...

10 September 2020 2,060 3 View

How can I improve Reinforcement Learning Agent training?

Hello everyone, I am trying to develop an RL agent for a simple double integrator system. Unfortunately, my agent couldn't find the maximum reward. The attached figure is the average episode...

20 July 2020 6,159 4 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to write a scientific report?

We are analysing scientific reports at University in great detail, so I wanted to find a scientific report about how to write a scientific report. Including detail such as what information to put...

02 March 2021 7,602 4 View

VIF very high, but correlation is low and coefficient is significant. Which one whould I choose?

Hello. I have a question whether if my coefficients (statistically significant) would be valid when VIFs are really high. In my model, there are independent variables(IV), moderating variables...

26 February 2021 956 13 View

What are the application of Fixed points thoery in Chemistry.?

It is said that fixed point theory has lot of applications not in the field of mathematics only but also in various areas. So I am looking for applications in Chemistry only..

26 February 2021 3,533 1 View

Data Analysis K-S and S-W tests?

Hello, I have conducted analysis where the K-W and S-W have come out as p

25 February 2021 9,648 3 View

Statistics: include groups of respondents made by one person for analysis?

Good morning, I could not find literature about this so I am asking. I am organizing data for a questionnaire (N=100) that foresees some personal questions like level of education. For the aim...

25 February 2021 2,090 4 View

Bayesian decision trees and bayesian regression trees in Python and/or R?

I am looking for implementation of bayesian decision trees and bayesian regression trees in Python and/or R.. Do you know if the existing libraries support this

23 February 2021 6,689 3 View

Can I ask did any good platform or journals for learning the calcluation on the reference governors and command governor?

Recently I face some problems with the mathematical ( calculation) on the reference governor and command governor, so I need some help from you all to get which platform or journal can let me...

23 February 2021 7,746 2 View