Can anyone provide some ideas on getting Yield Stress and Plastic Strain for Drucker-Prager Hardening in Drucker-Prager model in Abaqus?

Nahmed Nissar @Nahmed-Nissar

07 July 2017 1 341 Report

I need these values for modelling of Hostun Sand in Abaqus Software

Velusamy Gobinath

Dear Nahmed Nissar,

Following articles may be use full

http://www.ce.udel.edu/faculty/kaliakin/CEE_Report_surfaces.pdf

https://www.jstage.jst.go.jp/article/sandf1972/14/2/14_2_63/_pdf

http://www.icevirtuallibrary.com/doi/pdf/10.1680/geot.1958.8.1.22

https://doi.org/10.1139/t66-023

https://doi.org/10.1680/geot.1997.47.2.255

Badges
Science topic

Similar topics
Engineering
Modeling

More Nahmed Nissar's questions See All

Are results obtained from Material point Method (MPM) mesh dependent?

Are results obtained from Material point Method (MPM) mesh dependent? E.g, would using an unstructured mesh or semi-structure mesh give the same or different results? P.S. I am analyzing...

02 April 2020 5,117 0 View

Is there any electromagnetic simulation tool for UBUNTU OS?

Looking for a CST type tool for UBUNTU OS?

30 January 2019 1,734 4 View

What percentage of alcohol should be used to induce liver necrosis in Swiss albino rats?

I have to carry out hepatoprotective screening of few ethnomedicinal plants using alcohol as hepatotoxicant. I went through several papers, but none has mentioned the alcohol percentage orally to...

01 July 2015 6,073 7 View

Is it advisable to go with Soxhlet extraction of any plant material using water as solvent?

I have leaf powder of some plants. I am done with almost all the solvents I needed using Soxhlet, now the only left one is aqueous extraction. Please help, whether to continue with soxhlet or not...

03 August 2014 7,463 3 View

How to make CuO sol-gel?

I need to use it for incorporation onto CMOS dielectrics.

04 December 2013 8,946 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View