Can anyone provide line rating MVA for IEEE 14 bus lines?

More Alaaeldin M. Abdelshafy's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

It is possible to conduct a structured written interview for a qualitative study?

In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...

11 July 2024 4,163 4 View

What is Differential-Fed in microstrip patch ant? How it is design in CST studio? What is process and procedure to do Differential-Fed in CST studio?

What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?

08 July 2024 7,464 1 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

What is co-polarization and cross polarization? How can plot it from CST studio?

what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?

08 July 2024 7,869 1 View

Why in some degradation experiment the results doesn't fit first or second order kinetics ?

In an antibiotic degradation experiment using metals carbon composites to activate PMS, the results doesn't fit pseudo first or second order kinetics however the degradation efficiency is very...

26 June 2024 6,941 3 View

Why carrier Concentration decreases while increasing Temperature ?

Hi All . Recently, I conducted Hall measurement experiments at high temperatures on highly p-doped diamond with a doping concentration of 2.5×10^20 cm−3 During these experiments, I observed two...

23 June 2024 4,763 0 View

What are the best practices for increasing earth biomass?

I'm thinking of how to increase biomass to replace plastic and industrial waste.

23 June 2024 1,871 4 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

Mohammad Shahrazad

I reckon it is around 250. But plz check it again.

Zakieldeen Elhassan

It depends on the transformer rating, but it is around 100MVA, 230kV (L-L) and I was simulated this model in the PSCAD package program.

Alaaeldin M. Abdelshafy

thanks for all .but I need line rated MVA limit

Burc Deleen

Do you mean the operating limit relating to temperature?