Hi, I am using Ansys Apdl for fatigue crack growth. I need any one code to understand how it can be automized (recreating crack with node shift and remeshing).
Thank you
Find and read the Brith and Dead tech. in ANSYS APDL
Thanks Kyu In Shin, I will read that.
I am doing propagation life calculation of gas turbine disc under fatigue loading. I am doing this in ansys. i modeled surface crack in the model and calculated stress intensity factors k1,k2,k3....
04 May 2015 5,738 8 View
Hi, I'm trying to model crack propagation using ANSYS software in my thesis. I've got a question concerning crack tip mesh. I'm modeling eliptic surface crack in a plate using CTMOPT macro and...
31 December 2014 3,442 6 View
Hi, I am doing project on mixed mode crack growth of semi elliptical crack in gas turbine components under cyclic loading. Ansys has capability for finding J,K using CINT command. But, In mixed...
31 December 2014 2,232 3 View
Hi, I have four bodies in contact with common faces. I can't use "form a new part " feature for four parts. I didn't see any option to glue required solids. I am simulating a fracture problem. For...
09 October 2014 9,070 9 View
Hi, I am simulating a fracture problem. For that, I split a body into two bodies with slice by plane. That gives two faces at the same location (at intersection of bodies). Again, I split faces on...
09 October 2014 9,942 17 View
Hi, I used CTMOPT macro in Ansys classic to create semi elliptical crack with mesh in already existing model. But the macro is not working with different a/c ratio. In Ansys workbench tools are...
09 October 2014 1,099 6 View
I am starting FEA analysis in fracture mechanics. I want to know the best software for the analysis. I am familiar with Ansys. can anyone state the points for choosing better software for fea...
08 September 2014 1,015 11 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...
07 August 2024 2,569 1 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...
31 July 2024 3,913 6 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View