Can anyone please share the specific applications of weldments of dissimilar alloys (Titanium and Inconel)?

More Tauheed Shehbaz's questions See All

Islamic Leadership in the African American Community mosques?

Islamic Leadership in the African American Community mosques

12 January 2024 2,475 0 View

How to add type IIS restriction site sequence in primer for PCR amplification?

How to add type IIS restriction site sequence in primer for PCR amplification by using snapgene?

25 February 2023 9,789 1 View

How to add type II restriction site sequence in primer for PCR amplification? how much size can be add-in a plasmid?

how to add type II restriction site sequence in primer for PCR amplification? how much size can be add-in a plasmid?

24 February 2023 8,007 3 View

How and where i can purchasing a biobrick standard assembly?

Hi, Good Morning, I am working on multiple gene cloning and expression, for this purpose I need the Biobrick assembly. So please let me the price and availability of this assembly

15 November 2022 8,245 1 View

How Interpret Results of MOE docking, and how to draw publishable structure?

Hi Dear colleagues, I am working on MOE simulation, at the very beginning point of learning. I got stuck after docking, which structure and how the result will interpret for research publication.

21 November 2021 1,823 1 View

In HYSYS while defining feed pressure, whether the software takes atmospheric or vacuum as a datum mark?

I was simulating some experimental data on HYSYS and was finding issues in achieving consistency of data. When I have entered the pressures, assuming it to be gauge, the simulation shows many...

26 May 2018 7,538 2 View

I wrote a research paper on methane production from agricultural waste. I want to publish in journal of JCR list which are publishing in less time?

I have wrote a research paper on methane production from lignocellulosic biomass. I want to publish this paper in journal of JCR list which are publishing in less times?

20 October 2017 1,626 2 View

I am confusing about using Gompertz Equation on my data. I need to learn how to apply on data of biogas analysis ?

This equation is used for assessing the biogas production by anaerobic digestion.. Kindly help me...

20 September 2017 1,738 7 View

How the stack and shell temperature of hot oil heater can be decreased.?

Hot oil heater is a utility of Amine sweetening unit, which delivers the heat energy, via dow-therm thermal oil, to reboiler of ASU for production of steam and hence helping stripping process of...

08 April 2017 4,546 1 View

Can anybody help me in finding literature on every aspect of Stone Marten (Martes foina)?

I am facing difficulty in finding literature about Range, habitat biology of this species.

27 August 2014 6,256 10 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Are there instances where molecules with larger molecular weights exhibit greater mobility than those with smaller molecular weights?

Hi, I know that low molecular weight (MW) molecules generally tend to have higher mobility, while high molecular weight molecules tend to have lower mobility. However, in my experimental...

06 August 2024 1,495 2 View

For an in-vitro drug release study, what molecular weight cut-off (MWCO) dialysis bag is required for a 117 kDa protein?

kindly reply me. Thanking you in advance.

05 August 2024 7,727 4 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

Asmaa S.J.M Al-Ragehey

Yes

Tauheed Shehbaz

Will you please elaborate?( @ Asmaa S.J.M Al-Ragehey )

Jafar Jelokhani

Titanium is a light metal & low mass/volume ratio but inconel in a high temprature alloy

titanum used in stractural parts but inconel used in high temperature or hot parts.

if you have a position of two conditions, you can use and joint them.

i think in combustion chamber and burner bodies and honecomb seals you can find its joint. as brazed or TIGwelded