Can anyone please send me the complete simulation model of the paper which I am adding to?

More Debottam Bhunia's questions See All

Can anyone throw some light on MMC based control of traction drives using WBG semiconductor devices & provide some materials regarding this area?

I want to do research on above mentioned topic. Please, give me some guidelines to proceed towards this area. Hoping for a prompt & encouraging reply!

09 October 2017 7,036 0 View

What is benefit of using wide bandgap semiconductor devices in future power electronics?

Can I use WBG semiconductor device to control drives. Please, give me explanations. Hoping for a prompt & encouraging reply!

09 October 2017 7,352 3 View

What will be the hot research topics to do p.h.d in power electronics & drives?

If anyone wants to do p.h.d in power electronics & drives, which will be the hot research areas which has a future.

08 September 2017 9,446 0 View

Anyone provide me complete solution of the following problem?

In a 3 phase bridge inverter, 180 degree conduction mode, what will be power delivered to the load if the supply voltage of the inverter= 115V, ma (modulation index)= 0.5. Load is 3 phase 15 ohm...

07 August 2017 1,065 1 View

Can anyone provide me the pdf or any link to download generalized theory of electrical machines P.S. Bimbhra.

I need this book. Help in this regard will be highly appreciated!

06 July 2017 2,019 1 View

In which area of power electronics & drives, anyone should do research which is still obscure now-a-days?

If anyone wants to do p.h.d in power electronics & drives, what will be the hot topic to do research in this subject which is still unknown now-a-days. Help in this regard will be highly...

05 June 2017 2,405 5 View

If anyone is interested in space vector area, what should he choose to do research in this area?

If anyone wants to do research in space vector area, what topic should he choose in that area which is still obscure now-a-days.

05 June 2017 7,204 0 View

Is there any software to draw the diagram in MS word?

I need to write a thesis regarding power electronics. I need to draw the diagram in MS word 2007. Can anyone tell me whether any software is available to draw the diagram easily in MS word. If...

01 January 1970 2,932 8 View

What is the function of P in PI or PD controller?

Instead of PI or PD if we replace the system only by I or D, what will happen?Actually I need to know what will be the effect of system response. Also in fuzzy logic controller, if we don't...

01 January 1970 638 6 View

Can anyone be expert in SVPWM(power electronics & drives) without having programming skills?

If anyone wants to become expert in power electronics & drives( specially in SVPWM), does he need to know programming languages( like C, C++), should he have various software skills( like...

01 January 1970 2,091 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View