Hi
I faced following error in comsol,in fsi simulation and time dependent
error is:
condition for remeshing fulfilled for initial time
My simulation is artifical heart valve in comsol
Thanks you
Hi,
You can drop the question in the cosmol community forum , link below and also can look at the youtube video.
Cheers,
Sayan
https://www.youtube.com/watch?v=emUWAkUysf0
https://www.comsol.com/community/forums/
Please, use also this very interesting forum cfd-online. Good luck.
http://www.cfd-online.com/Forums
Maybe your remeshing doesn't start due to you setup
Thank Mr Shiuh-Hwa Shyu
Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?
25 February 2021 4,075 1 View
Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks
23 February 2021 6,518 3 View
I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...
18 February 2021 5,319 3 View
Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...
14 February 2021 3,606 2 View
The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...
08 February 2021 657 16 View
Currently using Msc Marc Mentat for FEA. Now i conduct the mesh convergence/sensitivity analysis manually. So I need to know if there any automatic way to conduct the mesh convergence/sensitivity...
04 February 2021 3,310 3 View
Hi everyone, I'm simulating a 3D turbulent pipe flow using the SST K-W turbulence model in ANSYS Fluent. Is there any quantity among the postprocessing quantities that represent "eddy size" or...
01 February 2021 731 1 View
Hi, I'm doing molecular dynamics on a 168 atoms system with a 20 A vacuum. To speed up my calculations, I set ALGO = Fast tag in INCAR, but surprisingly VASP crashes momentarily!. I have done a...
25 January 2021 9,876 3 View
Hi everyone I'm trying to pattern circular cross-section microfluidic channels in PDMS. The template is an optical fiber with an axially non-uniform diameter. To the best of my knowledge, there...
22 January 2021 2,352 2 View
Hello everyone, I'm a beginner on the simulation software ANSYS HFSS. I need to know how to measure the size of the generated field of my simulation. I have simulated a geometry that looked like...
20 January 2021 9,113 2 View
Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...
02 March 2021 4,624 4 View
How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...
02 March 2021 9,833 3 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...
24 February 2021 249 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.
23 February 2021 9,086 3 View
I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...
23 February 2021 4,050 1 View
Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?
22 February 2021 2,968 1 View
How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?
22 February 2021 5,408 1 View