I am trying to simulate phase change of refrigerant inside pipe extracting heat from panel in comsol. Can anyone help with how to simulate this?

My model is a rectangular multi layered structure under which refrigerant flows through cylindrical pipes. A heat flux of 600W/m2 applied on panel and internal forced convection is used for...

20 January 2021 9,478 1 View

Why does the ghost atoms gives error in NICS calculation with wb97xd in gaussian09 ?

In a trial, I am trying to calculate NICS (0 and 1) values for benzene ring using gaussian09. I have placed the ghost atoms at the center, 1A, and 2A above the rings. On using the method/basis...

19 January 2021 3,188 3 View

Rejected manuscript for journal publish after 1st revision, what needs to be done next?

Hello, My manuscript has been rejected by the editor and reviewers even after the 1st revision. Though I tend to disagree some of the points raised, assume I can't request for another revision...

28 December 2020 6,062 3 View

Acetylene reduction assay procedure?

Do anyone have the detailed step wise procedure(practical) to do the acetylene reduction assay? Or if anyone can let me know in which institute can i analyse my samples in India?

28 December 2020 6,717 2 View

What is the actual basis on which amount of Perovskites materials are to be taken?

In some discussion people took 112 mg of MAI and 461 mg of PbI2 in 1 mL DMF and some took 461mg of PbI2 too but 159mg of MAI there are many other authors took different amount of these materials...

17 September 2020 9,998 3 View

Forums to get online survey responses?

For my journal publish, I have been asked to increase the sample size by 200. I have been individually contacting more than 1000 Linkedin contacts and posted in all professional groups. But have...

04 September 2020 2,564 5 View

Derivation of Rice and Tracey equation???

12 July 2020 6,555 1 View

Can anyone suggest me where to get a low cost 2D Heterostructure Transfer System?

Except the 2D transfer system sold by HQ Graphene

09 July 2020 3,276 4 View

Why do mangroves intake oxygen through aerating roots like pneumatophores?

Many mangroves like Avicennia and Sonerratia species have developed pneumatophores as an adaptive strategy to survive in hypoxic environment. These pneumatophores receive oxygen from the...

16 April 2020 2,203 3 View

What is a popular book for understanding laser fundamentals and evolution and types of lasers?

I looking for books, channels, videos and PDFs regarding laser and particle interaction and evolution of laser power and laser types and how laser makes the physical changes on the ceramic...

05 April 2020 3,396 25 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View