01 January 2015 4 2K Report

I require DHA (Dehydroacetic acid). can anyone ,if possible, suggest simple and better yielding procedure for it?

More Ahmad Sayyad's questions See All
Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Why tick's salivary gland extract didn't run in the gel (SDS PAGE )??

Greetings, I want to make SDS PAGE for my sample (Tick salivery gland extract), I tried concentrations 10%, 12%. I also tried high molecular weight ladder. But the protein stopped at the top and...

25 February 2021 7,698 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

How to measure the pH of Peat Soil?

Peat possess organic content above 75% and is highly acidic in nature (i.e. pH < 4). Before commencing stabilization, it is mandatory to know about the pH level of peat. Therefore, your...

18 February 2021 9,424 7 View

How to Measure Consumer Willingness To Change from petroleum-fueled vehicle to electric vehicle?

I wanted to calculate the probability of one consumer shifting from using a petroleum-fueled vehicle to an electric vehicle. Since my background is in engineering I do not know much about how to...

15 February 2021 9,190 5 View

Having trouble mounting the sections on the slides for IHC staining, what solution should I use?

Hello everyone, I just started learning IHC staining and I have some frozen sections to practice with in a 96-well plate. I'm having trouble mounting the sections on the slide, a colleague told me...

08 February 2021 6,880 3 View

How to use Image Lab to take an image for the bands and the ladder in the same image merged together in Western Blot?

Hello everyone. I was trying to use Image Lab software to take an image of both the ladder and the samples merged together in one image to see the position of the bands according to the ladder MW,...

04 February 2021 9,996 2 View

Need a research paper for multi speaker and single microphone acoustic echo cancellation?

Hi, I am working on a problem that involves multiple smartphones/tablets. All devices are playing the same sound with synchronization difference up to +- 5ms. Now, there is an echo issue and I...

02 February 2021 5,929 3 View

Can I use the result from a pilot study to decide the minimum sample size ?

Can I use the result from a pilot study to decide the minimum sample size required to compare the means using independent sample t-test ? Or any other way that can help me to determine the...

29 January 2021 7,677 6 View

How to prepare secondary antibody from lyophilized antibody?

So I'm new to lab research and learning Western Blots these days. I ordered my secondary antibody and it arrived in a powdered form. Here is the...

27 January 2021 5,402 3 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close