Can 96-well common microplates handle DNS procotol/boiling?

09 September 2018 0 4K Report

I'm doing a DNS assay and tried to do the whole protocol directly in a 96-well microplate due to amount of samples to read and save reagents.

But, when I came to the step of boiling my reaction, the plate couldn't handle heat and ended up deformed.

Anyway, my fitting curve wasn't looking so good (my highest concentration was slightly darker than the blank but not as I have already seen in previous DNS in test tubes).

So, can anyone help with: Microplates can handle this protocol? Is there any microplate brand (I'm not looking for PCR plates) suggestions? What would be the right way of boiling my reaction in a microplate? Am I doing something in the wrong way?

Thanks!

Badges
Science method

More Victor Maricato's questions See All

Has anyone used TensorFlow in multi-variables optimization (e.g.: growth conditions for fungus)?

I am trying to explore some different approachs than MatLab for optimizing growth conditions with Neural Networks instead of conventional RSM. Does anyone know a repository or open-source code for...

04 May 2018 8,194 2 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

How to address this issue in the analysis of Real-Time PCR results?

To dear Researchers, I was analyzing a series of concentration for estimation of Real-Time PCR efficiency. The concentration was 1:10. I used MS-excel to evaluate Slope. The result of slope was -8...

01 March 2021 8,683 4 View

Runs of nucleotides in Sanger sequencing?

I performed site directed mutagenesis, transformation, and then I sent out plasmids for Sanger sequencing and found out that there is extension of DNA just before the stop codon. I am not sure...

27 February 2021 547 3 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

Calculating volume of DNA required from DNA concentration?

Hi I am a bit confused. They are asking me to find out the volume of DNA required in ul (a total of 30-100 ng for genomic DNA) from the DNA concentration in the nanodrop reading which was 404.8...

26 February 2021 5,029 2 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

What is a good reagent for lentiviral plasmid transfection in HeLa cells?

I have been using Lipofectamine 2000 but was hoping there may be a better protocol or one for something like Lipofectamine PLUS reagent.

24 February 2021 1,633 4 View

Could not amplify CD28 and CD3z ectodomain from cDNA of Jurkat Cells ?

For my experiments, I have to express ectodomains of human CD28 and CD3z. As a source, I extracted RNA from Jurkat cells and verified the quality of RNA on the gel. I, then, prepared cDNA using...

23 February 2021 7,051 4 View