Calculate beta with glmer.nb?

More Ran Dai's questions See All

Is there any materials that can be as flexible and stretchable as PDMS, while also having a small linear thermal expansion coefficient?

For the PDMS material, it's linear thermal expansion coefficient is about 3.2*10-4/℃. The polyimide has a smaller linear thermal expansion coefficient like 2*10-5/℃, but it cannot be stretch. It...

04 July 2024 4,525 1 View

How to eliminate imaginary phonon frequency in phonon dispersion of Coved Graphene Nanoribbons?

Dear all, I want to calculate the phonon dispersion of 4CNR-1-0 (structure is in Fig. 2 (b) in this article Designing coved graphene nanoribbons with charge carrier mob... ) and then calculate...

17 June 2024 6,911 2 View

How long can lyophilized cycloheximide be stored at 4℃?

I found a bottle of lyophilized cycloheximide in the lab refrigerator (4℃). I think lyophilized form should be rather stable, but it's been open for 3.5 years. Cell signaling says the lyophilized...

11 June 2024 8,366 0 View

How to measure the bisulfite concentration?

Does anyone know the exact BS concentration of the Zymo DNA methylation gold kit? or is there anyway to measure the BS concentration by titration? Thanks.

05 May 2024 8,848 1 View

What are the 3’ end modifications that prevent DNA from being extended by DNA polymerase? Which one has the best blocking effect? Leakage is minimal?

01 May 2024 5,188 5 View

How to calculate the slope for each participant in a two-way mixed anova analysis?

I am running a two-way mixed anova analysis with one IV is a between-subjects variable and another is a within-subjects variable (each participant was measured six times) and find a significant...

01 April 2024 7,184 1 View

Different species, same matrix, can I make different way to make STD and QC samples during method development and validation?

There days I was facing one challenge when doing MD and MV. I need to use rat and pig' plasma as matrix. I used to spike the solvent with different concentrations into the plasma to make STD and...

01 April 2024 3,766 0 View

How do we do prestressed concrete beam in LS Dyna with proper initial stress and strain in the precast portion of the concrete beam?

I am facing a problem with the simulation of the precast concrete beam with prestressing. Typically, a precast beam would be fabricated in the factory with prestressing tendons (precambering) to...

06 February 2024 1,046 1 View

Can BHQ quench the fluorescence of FAM in the case shown below?

28 January 2024 6,182 1 View

Migration in Lasius ants?

Do ants in the genus Lasius migrate? If so, what are some of the characteristics of their migratory routes? Cheers

03 December 2023 6,320 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Is there an alternative to a multinomial regression which allows the DV to be non mutually exclusive?

I am trying to analyse data from a survey examining what variables affect teachers perceived barriers to incorporating technology into their classroom. I have 5 predictor variables however my DV...

06 August 2024 1,752 3 View

In order to run Multinomial Logistic Regression, is it required that the data be in the long format?

I am using unit level data (IHDS round 2) & Stata 17

06 August 2024 5,725 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

David Eugene Booth

What does a standardized regression coefficient mean here and how would you standardize it anyway? D Booth

Ran Dai

Thanks David Eugene Booth I'm in the field and will get back to u soon - Ran

Standardized coefficients are with uniformed measurement units and are used for comparison of variable strength. I have trouble finding suitable r packages calculating beta for a glme.nb model.