Transparent colour problem in CST - Surface Current?

Hi everyone, I used CST to simulate the current distribution of an antenna. The results are ok but I have a problem with the colour display. As you can see in the attached file, the colour is...

02 March 2018 1,497 6 View

How to get the full inductance matrix from CST M-static?

Hi everyone, I am using the CST M-static to calculate the inductance of coils. For one coil, I can successfully get the self-inductance of it. I used current path. However, for two coil...

10 November 2017 1,740 3 View

How can I calculate the channel coefficient in cooperative networks?

Hello, everybody In the cooperative networks, is the channel coefficient from source to a relay calculated by the equation: h= sqrt(1 / (D^alpha)) * (1 / sqrt(2)) * (randn + i * randn) where D is...

10 November 2014 8,476 4 View

What is the minimum required OSNR?

I heard that the minimum OSNR of an optical fibre system is 22.7 dB. Is that correct? What is the reference for that conclusion?

07 August 2014 1,999 5 View

What is the optimal bandwidth in the equation of OSNR with four-wave mixing?

I am simulating the effect of FWM and ASE noise. finally, at the receiver OSNR= Pout/ ( Pfwm + S * BW * m) where the S is the ase density, m is the number of amplifier. I have 10 channels with...

07 August 2014 7,972 6 View

Does anyone have experience with Four-wave mixing?

Hi, I am working on four-wave mixing. Just a substitution of values to equation but I am very concerned about the unit of each factor. Please help me by calculating the typical power of FWM which...

06 July 2014 6,670 10 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Have someone successfully used the ER alpha (Santa Cruz sc-8002) antibody in immunostaining ?

Santa Cruz now recommends this new antibody (F-10) but I can't find a publication using this reference. I'm working on human et non human primate hypothalamus and so far, it doesn't work. Is...

02 March 2021 10,003 2 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View