I need a protocol for extracting ochratoxin A from green coffee beans for analysis on hplc, as well as the protocol for carrying out the calibr ?

ochratoxine A ; HPLC ; green coffee

29 December 2020 4,028 3 View

What is the most recommended multispectral-UAV to be used for delineating the shoreline?

Hi there, I am looking to purchase an UAV with an attached multi-spectral camera to use its images in delineate the shoreline. I need to take a vertical geo-referenced image (if possible) and...

21 November 2020 1,283 3 View

How can i delaying a signal in Matlab script file without using simulink block (i want the instruction of delaying a signal in script file ) ?

How can i delaying a signal in Matlab script file without using simulink block? (i want the instruction of delaying a signal in script file )

27 October 2020 4,299 2 View

What would you do if MgSO4 did not fully dry your organic extract ?

Hi everyone, I used MgSO4 as a drying agent to suck all water droplets from my organic extract. However, even after adding MgSO4 three times and leaving it overnight, I still see some water...

14 September 2020 9,203 3 View

What multiphase model should be used to simulate the evaporation of an oil droplet in ANSYS FLUENT?

Hello, we have a sheet of Aluminium and some droplets of oil on it. The temperature of the sheet increases and the oil droplet evaporates in the air. The droplet has water and kerosene too and...

29 August 2020 2,268 3 View

How to activate the solid species tab in species transport in ANSYS Fluent?

Hello, I have to add a solid catalyst to the mixture but the tab is not activated. I have defined the solid material in the materials section but the list is showing the fluid materials only. How...

19 July 2020 4,930 3 View

How to make intervals in an ANSYS Fluent user defined function UDF to describe three different equations through time?

Hello, I have a plot shows the change of a quantity with time. How can we write a code in Fluent UDF to compile it ? I need a way to define the time intervals. From start to a specific moment, the...

30 May 2020 5,774 10 View

How to numerically estimate the polarity graph of a PEM fuel cell like the attached paper?

Hello, how to estimate the voltage and the current density of a fuel cell and put both on a single graph using CFD simulations? The paper is attached. Thank you!

04 May 2020 8,228 5 View

Which family name is correct for the insect species listed in the table below?

Hi friends The following table shows insect species from 3 orders. In conflicting sources, they are introduced from different families (family 1, family 2 and family 3). What do you think about...

02 March 2020 5,140 3 View

How to calculate the battery coefficients of Y and U by trial and error to estimate the current density and battery performance?

Hello I have a paper shows an idea to validate the battery performance by trial and error. How can we estimate the coefficients of Y and U and what is the experimental data needed for...

25 December 2019 1,502 8 View

Energy minimization in LAMMPS using NVT ?

How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...

01 March 2021 2,294 3 View

How can I edit suggested publications?

Hi there! I regularly receive suggestion about papers and authors that are totally out of my area. Does anybody know how I can fix this? Thank you!

01 March 2021 9,574 4 View

How to improve RNA isolation?

Hi, I have been struggling with a weird issue for my RNA samples. I used the Qiagen RNA plus mini kit. For some reason no matter how careful I am with the washes, when I measure the RNA, I get...

22 February 2021 1,286 6 View

Can you perform the Murexide test on samples fixed in Formalin?

I have a fixed sample and would like to use the murexide reaction to test for uric acid composition. I no longer have fresh samples

22 February 2021 1,328 1 View

Monte Carlo simulation?

Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...

22 February 2021 3,680 4 View

How would I use a glycerol fixation to fix whole brain Drosophila tissue?

I need to take IF images with DAPI on a confocal but I need to use a glycerol fixation. Has anyone done this method before, if so how was it done? Thank you.

21 February 2021 3,081 3 View

How to get/count refractive index in gasses?

20 February 2021 8,202 6 View

Is there any general protocol for immunohistology staining?

I have some fixed slides of tissue and need to do some staining, but I am not sure where to start. There are many protocols online. Any suggestions?

17 February 2021 3,062 4 View

What is the cause of the banding obtained after purifying the PCR product with ExoSAPIT?

Hello We are working on a PCR product with an approximate size between 5000 and 7000 bp, we want to use it as a positive internal control, since we have sequenced it and it corresponds to the...

17 February 2021 2,896 3 View

How can a reference point be fixed to an attachment point in Abaqus?

I am currently trying to copy an assembly feature, that is present in an old version of the model I am using, onto a new model. The feature is a reference point that is fixed to an attachment...

16 February 2021 8,872 2 View