I am looking for works or documents regarding CFD analysis of micro-channel heat exchangers. Any documents would be helpful.
Thanks in advance.
Regards,
Rajesh.
I have recently observed that the CFD results shows significant variations with different initialization techniques (mainly standard, fmg and hybrid). What could be the technical reason for this...
07 August 2016 9,756 15 View
Even though theoretically 'symmetry' and 'periodic' boundary conditions are totally different, i found that the CFD results with either of them are very similar. Why it is so ?
05 June 2016 8,831 13 View
Can we get the information about flow separation using contours/plots/iso surfaces etc from ANSYS Fluent ? I understand how flow separation happens and i am interested in finding it out using...
05 June 2016 3,168 4 View
Recently i read couple of articles on the mesh in case of numerical simulation. One claimed, hex meshes yields better results and the other claims it is poly mesh that yields better results. Which...
02 March 2016 5,195 6 View
Is it difficult to converge a CFD problem with pressure inlet and pressure outlet boundary conditions ? I am looking for the reason today's this. thanks in advance. thanks & Regards, Rajesh.
02 March 2016 9,485 6 View
Does a same coil (heat exchanger) show different performance when used as evaporator and when used as condenser ? I would like to know this in both theoretical and practical case ? I expect the...
11 December 2015 1,111 11 View
Is it possible to simulate flow induced corrosion using ANSYS Fluent, if yes how ? Please share ideas or articles. Thanks in advance.
09 October 2015 8,951 1 View
Instead of starting with random guesses, is it beneficial to feed a know best into the population, while using genetic algorithm as the optimizing technique for a optimization problem. I would...
01 February 2015 8,076 14 View
I have written a python code to carry out genetic algorithm optimization, but it is too slow. I would like to know how to run the same in parallel ? For more clarity, another python code will be...
31 December 2014 6,163 14 View
I am aware of the individual definitions of both static and absolute pressure. Will the magnitude of static and absolute pressure be the same, even though definition wise they represent different...
10 November 2014 3,005 30 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,113 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,098 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,136 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,768 4 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,003 2 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,427 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,489 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,891 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View