18 September 2019 3 8K Report

I want to develop a ecological risk model for the measure and if were possible to predict the shrimp farming assessment in estuaries with mangroves in the north of Ecuador.

I have some ideas but I don´t about a basic protocole for ecological risk modelling.

Thanks in advanced

Eduardo Rebolledo Monsalve

More Eduardo Rodolfo Rebolledo Monsalve's questions See All
How can I publish my final master project as an article for a scientif journal?

I am interested in publishing an updated version of my final master´s project in Spain and i am not sure which steps to take. I am open to suggestions.

16 July 2024 7,431 1 View

THP-1 cells completely dying with PMA, help?

Have been trying to induce THP-1 using PMA at different concentrations (range from 5 to 50 ng/mL) but after 48h all the conditions except the control are mostly dead, checked by trypan blue and...

03 July 2024 3,884 5 View

Can anyone share the JCR impact factor for 2024?

Please can someone share the list of journals with impact factor published in 2024?

27 June 2024 2,927 0 View

Is is posible a negative eelative predicted relevance q2 in PLS SEM?

I am working on a paper and need to calculate the q2 value in a model. However, I found that some of the values are negative. I am trying to interpret these negative values. Does anyone have any...

26 June 2024 1,176 0 View

Is there an HSQC sequnce suitable for 13C labelled small molecules?

I work in glycobiology and one of my duties is synthesize short oligosaccharide with, at least, one sugar universally 13C-labelled. Is there any sequence that can help me with characterization,...

28 May 2024 8,039 0 View

Can someone tell me what is this on my petri dish?

Hi! I left some petri dishes with Pseudomonas aeruginosa cultivated in MHI in the fridge (8°C) during some time off, and when I came back, it was like this. This is just one plate out of many, and...

24 May 2024 5,149 3 View

¿Necesito 10 articulos cientificos en el campo de las comunicaciones?

Estos articulos deben tener estas caracteristicas resumir los siguientes aspectos metodológicos: tipo de enfoque de investigación (cuantitativo, cualitativo o mixto), objetivo, hipótesis, muestra...

15 May 2024 820 0 View

National Bibliography used to be an important source for libraries acquisition. I wonder if in your country it remains important for, can you tell me?

Until the early 2000s, the National Bibliography used to be an important source for the development of library collections, mainly for the acquisition of new items. I would like to know if in your...

23 April 2024 5,037 7 View

Could you please advise on the following matter? I need to ask within a questionnaire, the number of days each episode of disease last??

For example: Episode 1 2 days duration Episode 2 4 days Ep 3 and son on Many thanks in advance

13 April 2024 4,735 0 View

Why Virtual or Augmented reality are yet see as risk by some teachers in STEM teaching in develop critical thinking?

VR or AR can be a useful tool to improve the learning experience of students, mainly in STEM topics or contents considering the complexity and abstraction need to think in analitycal mode, focused...

09 April 2024 739 2 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

E-commerce businesses, COVID-19 and Entrepreneurial Strategies (innovation, proactiveness and risk-taking)?

Hello: I am looking for articles that address e-commerce businesses and COVID-19 survivors, as well as Entrepreneurial strategies that reflect e-commerce businesses. Blessings Evelyn Dempsey

05 August 2024 5,332 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close