Why I am getting negative peaks and unstable baseline on HPLC?

I am using a Bio-Rad column for 5-HMF detection and and RID. My mobile phase is 0.005 H2SO4 and when I run my sample I get one negative peaks and no clear peak for HMF

08 September 2019 8,079 14 View

Why is the activation energy determined using a flow reactor different from that estimated in a batch-type reactor?

Why is the activation energy determined using a flow reactor different from that estimated in a batch-type reactor? If reactants used (i.e., substrate, catalyst, and solvent) are the same,...

07 August 2019 5,242 12 View

Can you advise regarding RID detector detecting range for fructose and HMF?

10 November 2018 4,715 12 View

I used standard KHP as part of a mixed standard for (vario TOC cube) calibration to measure Octane content, the results were far from expected?

02 March 2017 6,467 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

How the wettability of rock sample can be changed by ageing in pure hydrocarbon oils only?

I want to do wettability analysis of hydrocarbon oil (octane)/rock/surfactant solution system. but to do the analysis first I have to make rock surface oil-wet. Since hydrocarbon oil does not have...

27 February 2021 5,383 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

How can Gamma Ray API units be converted to CPS (counts per second)?

Oil and gas companies run gamma ray tool and take readings in API units while Gamma ray is also noted in cps, so how these units can be converted into each other?

24 February 2021 7,545 2 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View