Can anyone recommend a lab to test 4" x 4" sheets for X-Ray attattenuation per ASTM F 2547-18 or 3094-14? preferably in Dallas, Texas area.
[email protected]
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
In Zn-Air Battery, how to plot Potential vs current density(mA/cm-2) in EC-Lab softare/BioLogic instrument. Please suggest. plot of the ref....
04 July 2024 3,807 2 View
and will i add phytochemical along with FUDR?
28 June 2024 6,254 0 View
As many of us know, there is often confusion regarding the alignment of dates, months, and seasons in our agricultural practices. To address this, I have prepared a table that aims to provide a...
27 June 2024 7,749 1 View
In Zn-Air Battery experiment, how to plot Potential vs current density(mA/cm-2) from discharge voltage curves. Please suggest.
23 June 2024 860 2 View
A masonry structure modelled all the wall using macro element and performing non linear time history analysis in dynamic explicit . I need to determine the random cracks where a give stress...
01 June 2024 1,349 1 View
Hi, I want to calculate the plastic equivalent strain for Mohr-Coulomb. I found a formula from Abaqus documentation. I have attached the photo of PEEQ calculation. But I want to figure out the...
28 May 2024 9,081 1 View
If the Fuzzy logic controller is not giving the desired results than what to do ? Further more...How to know how many membership functions and which type should be chosen?
20 May 2024 628 0 View
My student is isolating phages against ESKAPE pathogens, but she is getting a minute plaque. Can you please suggest how to get better results?
07 May 2024 9,554 2 View
I have added references using Mendeley reference manager, but it ruined the manuscript; it doesn't take ACS or other journals references properly except elsevier, and multiple duplicates are...
22 April 2024 6,560 1 View
This article is mine. It was republished by unknown person using an address (Wilson N Jones Regional Center, Sherman Texas USA. I have a patent.
10 August 2024 7,528 5 View
Require for Rietveld refinement in XRD.
08 August 2024 3,081 2 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
I want to refine one XRD peak of my in-situ xrd but the background is never working good which ultimately fails the refinement. How to refine and adjust the background using GSAS-II
05 August 2024 5,291 2 View
How to calculate the molar proportions of the oxides from the XRF analyses?
02 August 2024 2,565 2 View
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,789 4 View
What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?
30 July 2024 6,261 4 View
I will be doing an XRD on a sample which is powdered in natured and is a hydrogenated compound. I would like to know how we can understand the individual components and components by using the...
28 July 2024 4,548 2 View
I'm working with a hydrogel sample and I'd like to perform XRD analysis. Can anyone offer guidance on preparing the hydrogel for the XRD instrument? Specifically, I'm unsure about the best method...
20 July 2024 3,611 4 View
Can we measure the 2θ variation within a 5-degree range on a Bruker D2 Phaser XRD machine? I have experienced problems with diffraction angles (2θ) below 10 degrees. Is this range within the...
13 July 2024 2,615 4 View