It is needed so that the PE composite capable to withstand the harsh ambient condition.
Annealing of base material is necessary to remove internal stresses ..surface must be clean and dry
Interesting.
The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.
23 July 2024 3,205 0 View
I am new to research. The boiling point of triethyl amine (NEt3) is 89 degrees centigrade. I am skeptical that when I will let the hydrogen escape which is getting generated in situ, I will also...
21 July 2024 7,284 4 View
Sometimes I see the shadow like bands and its not true band. I want to know that what's the reason for it. I am using 2% gel for running genotyping samples I have uploaded the gel picture in both...
19 July 2024 148 6 View
What is the future scope of acoustic emission?
17 July 2024 1,510 1 View
I have a small molecule reagent with a boc-protected amino group. Now the reaction needs to be reacted at 37°C for 30 h. Is this protection group stable?
12 July 2024 3,745 2 View
What are the most effective remote sensing techniques and algorithms for detecting and analyzing land use and land cover (LULC) changes in rapidly urbanizing areas, and how do their accuracies and...
11 July 2024 6,695 1 View
I am trying to measure the plasmon resonance angle of gold film and pure water using the Kretschmann configuration and a 633nm laser. Without flowing water over the gold, I can detect a clear...
10 July 2024 4,719 3 View
My attempt to promote listening was "Using Short-stories". It works fairly but there could be better options. Role of Short Stories in Developing English Listening Skill
09 July 2024 9,078 4 View
I have tried to resolve this issue a little bit, but eager to get your insights and thoughts to make my efforts better. Using Homophones and Homographs in ESL Classrooms
04 July 2024 6,742 3 View
The contribution of "Distance Education" is immense, but still needs a lot of reforms. Universities generally adopt one another ideas and ignore the ideas of world wide scholars, distance...
04 July 2024 2,545 6 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View
For example, if low-density polyethylene (LDPE) is equilibrated with PCB contaminated marine and freshwater sediments, can LDPE-lipid partition coefficients be used to obtain equilibrium...
28 July 2024 263 1 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose
25 July 2024 438 3 View
I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...
23 July 2024 4,074 2 View
Hi everyone, Can someone explain for me a method to inject VOC collected with Tedlar bag from pyrolysis process and transfer or inject into GCMS. Thanks
22 July 2024 6,398 1 View
We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...
09 July 2024 5,123 4 View