Any body can help and suggest; how to define orientation of lamina during the modelling of thick composite plate in ANSYS/AUTODYN hydro code ?

12 December 2015 0 5K Report

composite plate modelling in AUTODYN hydro code.

Badges
Science topic

More Md Muslim Ansari's questions See All

Is digital image correlation technique (DIC) work to measure strain in specimen under ballistic impact?

Hi, Is digital image correlation technique (DIC) work to measure strain in specimen under ballistic impact or even in low velocity impact. Any input is highly appreciable. Thank you,

06 July 2018 2,596 0 View

Can you help me with an implementation in AUTODYN?

Can anyone suggest what values of parameters are used in polynomial equation of state should I take, while analysing kevlar epoxy laminate under impact in AUTODYN hydrocode.

31 December 2014 3,779 1 View

How can I eliminate the error "ACP Input Validation Failure. There is no data contained in the input mesh file" in ACP/Ansys?

I modeled a composite plate in Geometry module, then meshed in model, but error comes while edit in setup module in ACP. Error box attached here.

05 June 2014 2,473 8 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View