Any better tool for fuzzy modeling?

More Muhammed Kamrul Islam's questions See All

What is the basic difference between Mechanics and Applied Mechanics?

Is it only the rigid body analysis in mechanics and internal stress analysis for applied mechanics?

05 June 2016 1,605 1 View

Which method for risk assessment in process industry is best?

I want to apply a suitable and rigorous risk assessment method for process industries like refineries.

10 November 2015 2,359 3 View

How can I can solve the non nonlinear equation by newton rapson method using Jacobin matrix in MATLAB?

I want to solve it by MATLAB program The non linear equations are: log(x^2+y)-1+y=0; sqrt(x)+xy=0, initial approximation (x0,y0)=(2.4,-0.6) no. of iteration is 50

01 February 2015 8,899 3 View

How can I maximize the non linear function by Newton Rapson method using Hessian matrix in MATLAB?

I want to maximize the following equation using Newton Rapson Method in MATLAB:z= -(x1 - sqrt(5))2 - (x2-pi)2-10Initial Approximation:X0=[6.597, 5.891]T

01 February 2015 3,052 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

E-commerce businesses, COVID-19 and Entrepreneurial Strategies (innovation, proactiveness and risk-taking)?

Hello: I am looking for articles that address e-commerce businesses and COVID-19 survivors, as well as Entrepreneurial strategies that reflect e-commerce businesses. Blessings Evelyn Dempsey

05 August 2024 5,332 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Osman Ali Sadek Ibrahim

Hi,

Computer Science school, University of Nottingham provides Fuzzy tools such as Juzzy:

http://juzzy.wagnerweb.net/

Also, you can check computational intelligence with Matlab book.

Best wishes,

Osman

Konstantin Degtiarev

Hello Muhammed Kamrul Islam,

You can also try JuzzyOnline (http://ritweb.cloudapp.net:8080/JuzzyOnline/) to handle type-1 and type-2 (both interval and general) fuzzy systems ; actually, it uses Juzzy toolkit mentioned in the previous response. Guaje Fuzzy (https://sourceforge.net/projects/guajefuzzy/) can be an option either as well as FuzzyTech (www.fuzzytech.com) that can be used for free in demo mode. Fuzzy modeling is a broad domain, so it's better to understand the 'match' of the problem at hand to those features that are provided (supported) by the corresponding software.

With regards,

Konstantin Degtiarev / 02.07.2017

Yew-Chung Chak

Hi Kamrul,

What exactly is your problem in using MATLAB Fuzzy Logic Toolbox to develop fuzzy models?

Muhammed Kamrul Islam

Mr. Yew-Chung Chak

no problem, I am curious to check the same model with another tool.

Thank you all.

Mohammad Shah Alam

Hello Muhammed Kamrul Islam, You can also try JuzzyOnline (http://ritweb.cloudapp.net:8080/JuzzyOnline/) to handle type-1 and type-2 (both interval and general)

You can try to download www.informationvine.com/Fuzzy+Logic+Software‎