ANSYS Workbench - FAQS.TIPS

Abu Mohammed Sifullah @Abu_Mohammed_Sifullah

09 September 2014 0 7K Report

I want to simulate laser cutting by ansys workbench. I am very new in ANSYS Workbench. How i will use ekill.

Badges
Science topic

More Abu Mohammed Sifullah's questions See All

How can I deactivate an element after it exceeds the melting temperature in ANSYS?

I am doing research on laser cutting. I am trying to remove/ deactivate the element after exceeding the melting temperature. I tried by using following code. /SOLU ! Enter SOLUTION... ! Typical...

03 April 2015 4,382 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View