Why the use of paroxetine becomes less effective after long term use?

why the use of paroxetine and SSRI to treat panic and phobia becomes less effective after long term use, and is there any danger to eat serotonin containing food in association with those drugs?

06 July 2017 4,241 4 View

Well dowson polyoxometalates simulation error in gaussian and maestro schrodinger?

11 December 2015 9,706 0 View

Can any one help me analysing bromuconazole (a pesticide) samples with LC-MS or GC-MS?

can any one help me analyse bromuconazole samples with LC-MS or GC-MS, i will put him in my paper i am pHD student from algeria and i dont have the instrmentation

03 April 2015 4,553 4 View

Kolbe electrolysis of citrate salts?

what product we obtain in the anode when we electrochemically decarboxylate the sodium citrate for example

01 February 2015 4,411 0 View

how to get the "Vorticity Transport Equation" by taking the curl of "compressible Navier-Stockes" equation?

I read a paper on modeling a two dimensional salt gradient solar pond and the author said that he got the vorticity transport equation by applying the curl to the variable density Navier-Stockes...

31 December 2013 3,660 1 View

Natural convection of water over a hot horizontal plate using comsol

i want to simulate the natural convection of water with transient state over a heated metallic plate using comsol multiphysics. can anyone give me an idea from where can one begins?

01 January 1970 1,765 8 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View