How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

VIF very high, but correlation is low and coefficient is significant. Which one whould I choose?

Hello. I have a question whether if my coefficients (statistically significant) would be valid when VIFs are really high. In my model, there are independent variables(IV), moderating variables...

26 February 2021 956 13 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

How to remove the species data from rda data frame in R (only remain the sites/samples point)?

Dear everyone, When I using the rda function in r, I met this question. As you can see in the figure, there are a lot of deep blue points which refers to the species. But I would like remain...

15 February 2021 8,982 2 View

How to simulate enzymatic hydrolyis of sucrose in a CSTR coupled with ultrafiltration membrane with comsol?

Dear all, I am trying to simulate the enzymatic hydrolysis of sucrose with invertase in CSTR in Comsol. The reaction pathway is such that Sucrose + Water -> Fructose + Glucose. It is desired...

27 January 2021 2,525 4 View

How to design an Ultrafiltration membrane for a CSTR?

Dear all, I am designing an Ultrafiltration (UF) membrane coupled with a CSTR. It is desired to utilized a dead end stirred reactor. The main purpose is to separate the enzyme used from the final...

27 January 2021 7,924 1 View

Sb2Te3 thin film annealing and damage(break)?

21 January 2021 9,642 2 View

Is it possible to publish a paper contradicting Einstein's special relativity in any Journal?

I just developed a new theory on electromagnetic and plan to publish in a Journal. The findings are purely through strict mathematical derivation without any disputable assumptions and also...

13 January 2021 1,558 5 View

What is the significance of Per-Patient and Per-Tooth analysis in epidemiology?

Research in prevalence usually provide results in per-tooth/object level and per-patient level. What is the significance of these two values and which is actually more important/accurate? What are...

10 December 2020 4,248 4 View

For SIADH, does it cause edema and Hypertension?

I have found two teachings from different sources. One they said about blood volume increase and therefore the patient has oedema and hypertension. But, another source says when there is high...

08 December 2020 1,278 3 View

Does any one know how i can prepare liver tissue with transmission electron microscope with good fixation?

i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity

03 March 2021 8,890 1 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

Is there any published or unpublished statistics on dropout rate (Dose1 to Dose-2) for Covid-19 vaccination in India, US, UK or any other country?

Are there any published or unpublished statistics or papers on the dropout rate (Dose1 to Dose-2) for Covid-19 vaccination in India, USA, UK, or any other country where vaccination has started at...

28 February 2021 4,237 1 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Steps to calculate activation energy by coats & redfern method?

I'm a chemistry student and I'm researching the kinetic degradation of mixed plastic waste. I'm having trouble calculating the activation energy by the coats & Redfern method. The data that...

24 February 2021 974 1 View