06 June 2018 6 7K Report

Hi,

How to set the initial contact gap/penetration in Abaqus to zero like e.g. "Adjust to touch" in ANSYS?

We have some Geometries with with many penetrating Surfaces after the reimport. We would like to overcome that problem in a efficient way.

Thank you!

More Anton Melnikov's questions See All
How to calculate dispersion curves in a Brilloin zone with ANSYS?

I want to investigate the stop bands of periodical structures. Is it possible to calculate dispersion curves in a Brilloin zone with ANSYS or other FEM code? Is there may be some work around?

10 November 2017 2,641 4 View

How to obtain a gaussian mixture model from experimental data?

I have experimental data where a mixture in the histogram plot is obvious. What is an elegant way to create the gaussian mixture model fitting to the data? The data is 1D and there are more then 3...

01 January 1970 5,507 9 View

Publications about statistical noise levels (L90, L95 etc.)

I'm looking for publications like papers about the statistical noise levels like L90, L95 etc. May be something to the development or to the application in different fields. Thank You!

01 January 1970 9,590 3 View

Similar questions and discussions
Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Energy minimization in LAMMPS using NVT ?

How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...

01 March 2021 2,294 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close