1. Can I directly compare the plastic strain outputs obtained from updated Lagrangian and CEL formulations through ABAQUS?

06 November 2020 0 8K Report

I have been simulated a large deformation problem in ABAQUS through updated Lagrangian and coupled Eulerian-Lagrangian formulations. A very slight variation have been observed in the stress outputs but the strain outputs are quite different in magnitude. Can I directly compare the plastic strain outputs obtained from ABAQUS for these two formulations? Which strain measures are used in the ABAQUS for updated Lagrangian and CEL formulations?

Badges
Science topic

More Bhupendra Chand's questions See All

How do I convert concrete test data of stress vs strain to Abaqus input employing hyperbolic Drucker–Prager yield surface?

I have unconfined concrete cylinder test data of stress vs strain. I need to do abaqus modeling for confined concrete using Drucker Prager. However, the literature I am referring to just says that...

17 October 2023 629 1 View

Should Jaccard similarity index be expressed as a percentage or a decimal value?

For plant study sites

28 August 2023 6,721 2 View

Where should I store my protein after the bacterial expression followed by the purification?

I am expressing the protein in the E. coli host cell, followed by the purification using dialysis buffer (20 mM phosphate buffer, 100 mM NaCl, 2 mM EDTA, 0.01% sodium azide, pH 7) for 12 h at room...

22 August 2023 5,047 2 View

Q.1. In tga analysis, some percentage (0.5 to 0.8%) weight gain in case of plastic sample. what is the reason ?

In TGA analysis, 0.5 to 0.8% weight gain in case of plastic sample at initial temperature. please let me know the reason behind this if any one knows. Thank you

22 August 2023 7,485 10 View

Which software is best to generate begomoviral genome map? What is the best software to generate a begomoviral genome map?

Dear Researcher, Different software tools can produce maps similar to the ones above. How can I find the best software for making genome maps like this?

22 August 2023 1,525 1 View

Suggestions for specific markers for cytoplasmic, nuclear and membrane fractions for western blot analysis?

I did the subcellular fractionation of transfected HEK-293T cells. For western blot analysis for the purity of fractions, I used anti-B actin antibody, anti-fibrillarin G4 antibody and...

18 July 2023 1,265 2 View

Why do we use inbred lines?

Inbred lines can capture and enhance the efficiency of heterosis breeding. Development of inbred lines in a perennial crop takes many years and requires experimental space.

14 July 2023 4,993 2 View

Can millets feed the population?

Millets are a group of small-seeded grains cultivated for thousands of years in many parts of the world. They are a great source of nutrition, high in fibre and rich in vitamins, minerals and...

24 June 2023 2,512 4 View

. What is the significance of mutation breeding?

Mutation breeding and plant mutagenesis as a significant role in increasing the genetic variability for desired traits in various food crops.

06 June 2023 7,257 4 View

What are the economic benefits of plant breeding?

Higher yields per unit of arable land increase the supply of primary agricultural products to international markets

03 June 2023 1,880 3 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View