Why mutual inductor takes high current at no load condition?

More Naeem Pasha's questions See All

Can I see nanoparticles using optical microscope with stage micrometer?

I am working on Solid Lipid Nanoparticles I am doing MPhil research I am preparing a formulation My topic is Preparation AND Evaluation of Indomethacin Loaded Solid Lipid Nanoparticles for...

27 October 2020 9,496 4 View

To what extant the GIS Thematic Mapping Approach is significant in the analysis?

Today, GIS is being considered the most significant and highly recommended technique in analyzing data and its also argued that in Pakistan too few people use this approach in the analysis of...

12 March 2020 5,317 5 View

How to calculate the elemental concentration in infusion and decoction?

If infusion was prepared by adding 2g of dry tea powder to 200mL boiling water (ratio of 1g per 100mL) for 10 minutes. It gives a factor of 100 for multiplication with instrumental concentration...

16 January 2020 1,844 3 View

What's the best way to detect the extracted lipids in order to confirm that your lipid extraction protocol is correct?

I am extracting Lipids from RBC Membranes using the Cholorform/Methanol (2:1) method. After phase separation and consequent evaporation of the organic phase, what would be the best way to confirm...

02 December 2019 8,050 2 View

Anybody can suggest me any solution why matlab stop working?

I installed different versions of MATLAB. After successful installation, when open the command or editor window, it is freezed/hanged. Before that it was working properly and suddenly start facing...

30 July 2019 4,244 3 View

The study of Marxist literary work in Pakistan.I want to know how Mohsin Hamid deals with economic disparities in his novels?

The focus of my attention is on Mohsin Hamid's novel How to get filthy rich in rising Asia?

21 December 2018 4,371 2 View

Hello dears; can anybody help in arranging data in excel multivariate analyses using repeated measures in SPSS?

08 April 2018 8,188 5 View

How do install CFD OpenFOAM on Centos 6.4 on computer nodes (cluster)?

We are facing dependencies while installing CFD OpenFOAM software while installing it at cluster. We dont have docker? How do we manage it? Your valuable suggestions are welcome. Thanks in...

13 March 2018 1,279 3 View

Can I perform histopathology on cell lines?

I have transfected cell line with an inhibitor of a particular gene. that gene promotes tumor growth. Now I want to check whether the inhibitor has caused change in the tumor growth. So can I do...

25 February 2018 142 6 View

Should i use 1 octane sulphonic acid instead of TFA(triflouroacetic Acid) in HPLC reverse phase|?

should i use 1 octane sulphonic acid instead of TFA(triflouroacetic Acid) in HPLC reverse phase as both are ion pairing agents?

28 January 2018 5,128 6 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View