Why is the Aluminium based Filler not used for Brazing of Steel ?

12 December 2014 1 7K Report

Joining of Metals & Alloys

Is there any other issues, besides brittle intermetallics formations, such as poor wetting of Steel by molten Aluminum ?

Badges
Science topic

More Rajan Biswas's questions See All

Is there any cracked version available TuFLOW software? How to get tutorials of this software?

Is there any cracked version available TuFLOW software? How to get tutorials of this software . As i want to use for modified shallow water equation in urban flood modeling and simulation

06 July 2024 2,741 0 View

There are any alternative software Infoworks or Mike for urban flooding?

please suggest if there are any cracked versions of these software available.

04 July 2024 8,704 2 View

Which solvent and substrate is found to be best suited for deposition of electrodes with MXene ink?

Suppose we have dried MXene slurry (Ti3C2Tx), then the combination of which solvent (in which this dried MXene slurry powder will be mixed, subsequently forming the "ink") and corresponding...

13 June 2024 5,763 0 View

Do you think academia, particularly in the humanities and social sciences, is a continuum of semantic tricks?

Every concept feels like its predecessors stated it more precisely, with successors just adding context. It's rewording, but the understanding stays the same. For example: Structuralism, as...

10 June 2024 3,979 0 View

Can the aims outlined by a translator in the preface be understood as Skopos?

Skopos theory, developed by Hans Vermeer, is a functionalist approach to translation that emphasizes the purpose (Skopos) of a translation as the primary factor guiding the translation process....

02 June 2024 761 3 View

Which institute in India has Intelligent gravimetric analyzer for hydrogen gas storage?

16 May 2024 9,115 0 View

What type of validity is measured for questionnaires by Product Moment Pearson Correlation in SPSS?

Product Moment Pearson Correlation was done in SPSS for the validity test by correlating each item's questionnaire scores with the total score. What type of validity (content/ criterion/ construct...

27 April 2024 4,753 2 View

I am trying to resolve immune cytokines. Which is the right percentage of SDS resolving gel?

I wish to resolve IL-6 (mol wt= 21-26KDa), TNF- alpha (17.3-17.4 KDa), GMF-beta (16.7 KDa), GAPDH (36kDa) and PDL1 (40-70 KDa). I think 12.5% gel is good to go. Is it advisable or should I go for...

25 April 2024 9,798 0 View

How do i calculate cut off values in ELISA?

I am running ELISA for different biomarkers against meningitis. I need to know how to calculate cutoff values for it in ELISA. There is no negative control or positive control for these kits,...

07 April 2024 3,079 1 View

How can we induce drought stress in rice plants in vitro? What methods measure stress( MPa) accurately?

This question seeks to explore the techniques for inducing drought stress in rice plants in laboratory conditions and methods for accurately assessing the resulting MPa stress levels. It aims to...

17 March 2024 5,840 0 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View