18 January 2024 1 8K Report

Why do Aluminum cells need to be kept at a higher temperature when the equipment is on standby? Will aluminum cause damage to the crucible after condensation? In addition, why is it necessary to replace the crucible when replenishing the aluminum source material?

  • Similar topics
  • Heat
More Jin Zhu's questions See All
How to classify strictly upper triangular matrices by similarity?

Let F be a field. Consider U, the set of n times n strictly upper triangular matrices in F. For X, Y in U, we call them similar if there exists some S, which is non-degenerate and upper...

01 March 2021 2,957 8 View

Can anyone please help me in processing SAR SLC data to generate interferogram using SNAP?

I have two scenes of the study area, one top and the other bottom. As per the tutorials and papers published, the step include coregistering the master sand slave images. However, when i try to...

24 February 2021 6,372 1 View

I have faced a problem to amplify VP2 gene of porcine parvovirus 1,2,3 and 5? Please suggest me how can i solve this problem?

Till now i haven't got any PCR amplified vp2 gene bands on specific annealing temperature and in step up PCR.

08 February 2021 819 4 View

I am looking to develop a basic oral microbiome assay. Can anyone advise on culture vessel, conditions and organisms that require minimal maintenance?

I am looking to investigate oral care products with an easy-to-prepare culture of orally derrived microorganisms.

21 January 2021 3,448 1 View

Why does the fatigue cracks initiate from surface to interior as the stress level decreases?

It is well known that low-cycle and high-cycle fatigue cracks initiate from the surface, while ultra-high cycle fatigue cracks initiate from the inside. I am very curious why this transformation...

17 January 2021 9,633 6 View

In which solvent dissolve silver nanoparticles for XRD pattern study through NMR ?

The silver nanoparticles, which are solid form and I want to study the XRD pattern of this nanoparticles by Nuclear Magnetic Resonance (NMR), so I asked which solvent are used for dissolve of...

13 January 2021 3,434 4 View

How much the nanoparticles reach the inflammatory tissue?

Dear colleagues, I want to know the average analysis data of EPR effect on inflammatory tissue (acute lung inflammation/injury, ischemia/reperfusion, rheumatoid arthritis, and sepsis..) In...

22 December 2020 3,147 2 View

How to understand the chemo-mechanical coupling?

Recently, I came into contact with a new discipline named chemo-mechanical coupling. I found that chemo-mechanical coupling phenomena exist in many research areas, ranging from development of...

17 December 2020 1,065 3 View

I am working on membrane distillation model in COMSOL and I have some problems coming in it?

I need to add a latent heat flux of evaporation to the hot side boundary, which is a function of the pressure difference between the cold side and the hot side boundary.However, the pressure at...

16 December 2020 9,890 1 View

RNA Binding Proteins?

Anyone of you worked to extract RNA binding proteins?

07 December 2020 5,810 3 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close